參數資料
型號: PIC14000
廠商: Microchip Technology Inc.
英文描述: CTV 22C 22#22D SKT RECP
中文描述: 28引腳可編程混合信號控制器
文件頁數: 46/152頁
文件大?。?/td> 953K
代理商: PIC14000
PIC14000
DS40122B-page 46
Preliminary
1996 Microchip Technology Inc.
When a master does not wish to relinquish the bus (by
generating a STOP condition), a repeated START (Sr)
must be generated. This condition is identical to the
START (SDA goes high-to-low while SCL is high), but
occurs after a data transfer acknowledge pulse (not the
bus-free state). This allows a master to send
“commands” to the slave and then receive the
requested information or to address a different slave
device. This sequence is shown in Figure 7-10.
FIGURE 7-8:
MASTER - TRANSMITTER SEQUENCE
FIGURE 7-9:
MASTER - RECEIVER SEQUENCE
FIGURE 7-10: COMBINED FORMAT
For 7-bit address:
S Slave Address R/W A DATA A DATA A/A
P
"0" (write)
data transferred
(n bytes - acknowledge)
A master transmitter addresses a slave receiver with a
7-bit address. The transfer direction is not changed.
For 10-bit address:
S Slave Address
first 7 bits
R/W A1Slave Address
second byte
A2
(write)
A master transmitter addresses a slave receiver with a
10-bit address.
From master to slave
From slave to master
A = acknowledge (SDA low)
A = not acknowledge (SDA high)
S = START condition
P = STOP condition
Data A
Data
P
A/A
For 7-bit address:
S Slave Address R/W A DATA A DATA
A
P
(read)
data transferred
(n bytes - acknowledge)
A master reads a slave immediately after the first byte.
For 10-bit address:
S Slave Address
first 7 bits
R/W A1Slave Address
second byte
A2
(write)
A master transmitter addresses a slave receiver with a
10-bit address.
From master to slave
From slave to master
A = acknowledge (SDA low)
A = not acknowledge (SDA high)
S = START condition
P = STOP condition
Sr Slave Address
first 7 bits
R/W A3 Data A
Data
P
A
(read)
S Slave Address R/W A DATA A/A
(read or write)
(n bytes + acknowledge)
Transfer direction of data and acknowledgement bits depends on R/W bits.
Combined Format:
S Slave Address
first 7 bits
R/W A Slave Address
second byte
A
(write)
Combined format -
From master to slave
From slave to master
A = acknowledge (SDA low)
A = not acknowledge (SDA high)
S = START condition
P = STOP condition
Sr Slave Address
first 7 bits
R/W A Data A
Data
P
A
(read)
Sr Slave Address R/W A DATA A/A P
Sr = repeated
START condition
Direction of transfer
may change at this point
Data A
Data A/A
A master addresses a slave with a 10-bit address, then transmits
data to this slave and reads data from this slave.
(read)
(write)
相關PDF資料
PDF描述
PIC16C621A EPROM-Based 8-Bit CMOS Microcontroller
PIC16C62X EPROM-Based 8-Bit CMOS Microcontroller
PIC16C620A EPROM-Based 8-Bit CMOS Microcontroller
PIC16C622A EPROM-Based 8-Bit CMOS Microcontroller
PIC16CR620A EPROM-Based 8-Bit CMOS Microcontroller
相關代理商/技術參數
參數描述
PIC14000/JW 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC14000-04/SO 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC14000-04/SP 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC14000-04/SP 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 14000 SDIL28
PIC14000-04/SS 功能描述:8位微控制器 -MCU 7KB 192 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT