參數資料
型號： PIC12F675
廠商： Microchip Technology Inc.
英文描述： 8-Pin, 8-Bit CMOS Enhanced FLASH Microcontroller with A/D Converter and EEPROM Data Memory(-2.5~5.5V,具ADC,閃速微控制器)
中文描述： 8引腳，8位閃存微控制器的CMOS增強與A / D轉換器和EEPROM數據存儲器（-2.5?5.5V的，具藝術發展局，閃速微控制器）
文件頁數： 91/170頁
文件大?。?/td> 4191K
代理商： PIC12F675
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 89
PIC16F62X
13.3
READING THE EEPROM DATA
MEMORY
To read a data memory location, the user must write the
address to the EEADR register and then set control bit
RD (EECON1<0>). The data is available, in the very
next cycle, in the EEDATA register; therefore it can be
read in the next instruction. EEDATA will hold this value
until another read or until it is written to by the user
(during a write operation).
EXAMPLE 13-1:
DATA EEPROM READ
BSF
MOVLW
MOVWF
BSF
MOVF
BCF
STATUS, RP0
CONFIG_ADDR
EEADR
EECON1, RD
EEDATA, W
STATUS, RP0
; Bank 1
;
; Address to read
; EE Read
; W = EEDATA
; Bank 0
13.4
WRITING TO THE EEPROM DATA
MEMORY
To write an EEPROM data location, the user must first
write the address to the EEADR register and the data
to the EEDATA register. Then the user must follow a
specific sequence to initiate the write for each byte.
EXAMPLE 13-2:
DATA EEPROM WRITE
BSF
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
STATUS, RP0
EECON1, WREN
INTCON, GIE
55h
EECON2
AAh
EECON2
EECON1,WR
; Bank 1
; Enable write
; Disable INTs.
;
; Write 55h
;
; Write AAh
; Set WR bit
; begin write
; Enable INTs
.
INTCON, GIE
The write will not initiate if the above sequence is not
exactly followed (write 55h to EECON2, write AAh to
EECON2, then set WR bit) for each byte. We strongly
recommend that interrupts be disabled during this
code segment. A cycle count is executed during the
required sequence. Any number that is not equal to the
required cycles to execute the required sequence will
cause the data not to be written into the EEPROM.
Additionally, the WREN bit in EECON1 must be set to
enable write. This mechanism prevents accidental
writes to data EEPROM due to errant (unexpected)
code execution (i.e., lost programs). The user should
keep the WREN bit clear at all times, except when
updating EEPROM. The WREN bit is not cleared
by hardware.
After a write sequence has been initiated, clearing the
WREN bit will not affect this write cycle. The WR bit will
be inhibited from being set unless the WREN bit is set.
At the completion of the write cycle, the WR bit is
cleared in hardware and the EE Write Complete
Interrupt Flag bit (EEIF) is set. The user can either
enable this interrupt or poll this bit. The EEIF bit in the
PIR1 registers must be cleared by software.
13.5
WRITE VERIFY
Depending on the application, good programming
practice may dictate that the value written to the Data
EEPROM should be verified (Example 13-3) to the
desired value to be written. This should be used in
applications where an EEPROM bit will be stressed
near the specification limit.
EXAMPLE 13-3:
WRITE VERIFY
BSF STATUS, RP0
MOVF EEDATA, W
BSF EECON1, RD
; Bank 1
; Read the
; value written
;
; Is the value written (in W reg) and
; read (in EEDATA) the same
;
SUBWF EEDATA, W
BCF
STATUS, RP0
BTFSS STATUS, Z
GOTO WRITE_ERR
:
:
;
; Bank0
; Is difference 0
; NO, Write error
; YES, Good write
; Continue program
13.6
PROTECTION AGAINST
SPURIOUS WRITE
There are conditions when the device may not want to
write to the data EEPROM memory. To protect against
spurious EEPROM writes, various mechanisms have
been built in. On power-up, WREN is cleared. Also, the
Power-up
Timer
(72
EEPROM write.
ms
duration)
prevents
The write initiate sequence, and the WREN bit together
help prevent an accidental write during brown-out,
power glitch, or software malfunction.
13.7
DATA EEPROM OPERATION
DURING CODE PROTECT
When the device is code protected, the CPU is able to
read and write unscrambled data to the Data
EEPROM.
R
S
相關PDF資料
PDF描述
PIC12F676 8-Pin, 8-Bit CMOS Enhanced FLASH Microcontroller with A/D Converter and EEPROM Data Memory(-2.5~5.5V,具ADC,閃速微控制器)
PIC12F680 8-Pin, 8-Bit CMOS Enhanced FLASH Microcontroller with Serial I/O Interface(-2.0~5.5V,串行I/O接口,閃速微控制器)
PIC12F681 8-Pin, 8-Bit CMOS Enhanced FLASH Microcontroller with Serial I/O Interface(-2.0~5.5V,串行I/O接口,閃速微控制器)
PIC16C164 OTP 8-Bit High-Performance CMOS Microcontroller(主從模式，工作電壓3.0~5.5V，2路PWM的微控制器)
PIC16C165 OTP 8-Bit High-Performance CMOS Microcontroller(主從模式，工作電壓3.0~5.5V，2路PWM的微控制器)
相關代理商/技術參數
參數描述
PIC12F675 DEVELOPMENT BOARD KIT 功能描述:DEVELOPMENT BOARD FOR PIC12F675 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:*
PIC12F675 DEVELOPMENT KIT 功能描述:EMBEDDED C DEVELOPMENT KIT RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
PIC12F675 I/SN0547 制造商:Microchip Technology Inc 功能描述:
PIC12F675-E 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, Flash-Based 8-Bit CMOS Microcontrollers
PIC12F675-E/MD 功能描述:8位微控制器 -MCU 1.75KB 64 RAM 6I/O Ext Temp QFN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*