- 您現在的位置：買賣IC網 > PDF目錄11617 > PIC12F1840T-I/SN (Microchip Technology)MCU 7KB FLASH 256B RAM XLP 8SOIC PDF資料下載
參數資料
| 型號： | PIC12F1840T-I/SN |
| 廠商： | Microchip Technology |
| 文件頁數： | 71/122頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 7KB FLASH 256B RAM XLP 8SOIC |
| 標準包裝： | 3,300 |
| 系列： | PIC® XLP™ 12F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 32MHz |
| 連通性： | I²C，LIN，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 5 |
| 程序存儲器容量： | 7KB（4K x 14） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 256 x 8 |
| RAM 容量： | 256 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.3 V ~ 5.5 V |
| 數據轉換器： | A/D 4x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
PIC12(L)F1840
DS41441B-page 52
Preliminary
2011 Microchip Technology Inc.
5.2.2
INTERNAL CLOCK SOURCES
The device may be configured to use the internal oscil-
lator block as the system clock by performing one of the
following actions:
Program the FOSC<2:0> bits in Configuration
Word 1 to select the INTOSC clock source, which
will be used as the default system clock upon a
device Reset.
Write the SCS<1:0> bits in the OSCCON register
to switch the system clock source to the internal
oscillator during run-time. See Section 5.3
for more information.
In INTOSC mode, OSC1/CLKIN is available for general
purpose I/O. OSC2/CLKOUT is available for general
purpose I/O or CLKOUT.
The function of the OSC2/CLKOUT pin is determined
by the state of the CLKOUTEN bit in Configuration
Word 1.
The internal oscillator block has two independent
oscillators and a dedicated Phase-Locked Loop,
HFPLL that can produce one of three internal system
clock sources.
1.
The
HFINTOSC
(High-Frequency
Internal
Oscillator) is factory calibrated and operates at
16 MHz. The HFINTOSC source is generated
from the 500 kHz MFINTOSC source and the
dedicated Phase-Locked Loop, HFPLL. The
frequency
of
the
HFINTOSC
can
be
user-adjusted via software using the OSCTUNE
register (Register 5-3).
2.
The MFINTOSC (Medium-Frequency Internal
Oscillator) is factory calibrated and operates at
500 kHz. The frequency of the MFINTOSC can
be user-adjusted via software using the
OSCTUNE register (Register 5-3).
3.
The
LFINTOSC
(Low-Frequency
Internal
Oscillator) is uncalibrated and operates at
31 kHz.
5.2.2.1
HFINTOSC
The High-Frequency Internal Oscillator (HFINTOSC) is
a factory calibrated 16 MHz internal clock source. The
frequency of the HFINTOSC can be altered via
software using the OSCTUNE register (Register 5-3).
The output of the HFINTOSC connects to a postscaler
and multiplexer (see Figure 5-1). One of nine
frequencies derived from the HFINTOSC can be
selected via software using the IRCF<3:0> bits of the
OSCCON register. See Section 5.2.2.7 “Internal
for more information.
The HFINTOSC is enabled by:
Configure the IRCF<3:0> bits of the OSCCON
register for the desired HF frequency, and
FOSC<2:0> = 100, or
Set the System Clock Source (SCS) bits of the
OSCCON register to ‘1x’.
The High Frequency Internal Oscillator Ready bit
(HFIOFR) of the OSCSTAT register indicates when the
HFINTOSC is running and can be utilized.
The High Frequency Internal Oscillator Status Locked
bit (HFIOFL) of the OSCSTAT register indicates when
the HFINTOSC is running within 2% of its final value.
The High Frequency Internal Oscillator Status Stable
bit (HFIOFS) of the OSCSTAT register indicates when
the HFINTOSC is running within 0.5% of its final value.
5.2.2.2
MFINTOSC
The
Medium-Frequency
Internal
Oscillator
(MFINTOSC) is a factory calibrated 500 kHz internal
clock source. The frequency of the MFINTOSC can be
altered via software using the OSCTUNE register
(Register 5-3).
The output of the MFINTOSC connects to a postscaler
and multiplexer (see Figure 5-1). One of nine
frequencies derived from the MFINTOSC can be
selected via software using the IRCF<3:0> bits of the
OSCCON register. See Section 5.2.2.7 “Internal
for more information.
The MFINTOSC is enabled by:
Configure the IRCF<3:0> bits of the OSCCON
register for the desired HF frequency, and
FOSC<2:0> = 100, or
Set the System Clock Source (SCS) bits of the
OSCCON register to ‘1x’
The Medium Frequency Internal Oscillator Ready bit
(MFIOFR) of the OSCSTAT register indicates when the
MFINTOSC is running and can be utilized.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16LF1902T-I/SS | MCU 3.5KB FLASH 128B RAM 28SSOP |
| PIC16LF720T-I/ML | MCU PIC 3.5KB FLASH 20QFN |
| PIC16F720T-I/ML | MCU PIC 2K FLASH 20-QFN |
| PIC16LF722AT-I/SS | MCU 8BIT 2K FLASH XLP 28-SSOP |
| PIC16F722AT-I/SS | MCU 8BIT 2K FLASH XLP 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12F505 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F505TE/MC | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F505TE/MG | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F505TE/MS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F505TE/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8/14-Pin, 8-Bit Flash Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。