- 您現在的位置：買賣IC網 > PDF目錄369995 > PF48F4P0ZTQ0 (Intel Corp.) Circular Connector; MIL SPEC:MIL-C-26482, Series I, Solder; Body Material:Aluminum; Series:PT00; No. of Contacts:10; Connector Shell Size:12; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle PDF資料下載
參數資料
| 型號： | PF48F4P0ZTQ0 |
| 廠商： | Intel Corp. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; MIL SPEC:MIL-C-26482, Series I, Solder; Body Material:Aluminum; Series:PT00; No. of Contacts:10; Connector Shell Size:12; Connecting Termination:Solder; Circular Shell Style:Wall Mount Receptacle |
| 中文描述： | 英特爾StrataFlash嵌入式存儲器 |
| 文件頁數： | 49/102頁 |
| 文件大?。?/td> | 1609K |
| 代理商： | PF48F4P0ZTQ0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
1-Gbit P30 Family
Datasheet
Intel StrataFlash
Embedded Memory (P30)
Order Number: 306666, Revision: 001
April 2005
49
9.1.2
Writes
To perform a write operation, both CE# and WE# are asserted while RST# and OE# are deasserted.
During a write operation, address and data are latched on the rising edge of WE# or CE#,
whichever occurs first.
Table 20, “Command Bus Cycles” on page 50
shows the bus cycle
sequence for each of the supported device commands, while
Table 21, “Command Codes and
Definitions” on page 51
describes each command. See
Section 7.0, “AC Characteristics” on
page 33
for signal-timing details.
Note:
Write operations with invalid V
CC
and/or V
PP
voltages can produce spurious results and should not
be attempted.
9.1.3
Output Disable
When OE# is deasserted, device outputs DQ[15:0] are disabled and placed in a high
-
impedance
(High-Z) state, WAIT is also placed in High-Z.
9.1.4
Standby
When CE# is deasserted the device is deselected and placed in standby, substantially reducing
power consumption. In standby, the data outputs are placed in High-Z, independent of the level
placed on OE#. Standby current, I
CCS
, is the average current measured over any 5 ms time interval,
5
μ
s after CE# is deasserted. During standby, average current is measured over the same time
interval 5
μ
s after CE# is deasserted.
When the device is deselected (while CE# is deasserted) during a program or erase operation, it
continues to consume active power until the program or erase operation is completed.
9.1.5
Reset
As with any automated device, it is important to assert RST# when the system is reset. When the
system comes out of reset, the system processor attempts to read from the flash memory if it is the
system boot device. If a CPU reset occurs with no flash memory reset, improper CPU initialization
may occur because the flash memory may be providing status information rather than array data.
Flash memory devices from Intel allow proper CPU initialization following a system reset through
the use of the RST# input. RST# should be controlled by the same low-true reset signal that resets
the system CPU.
After initial power-up or reset, the device defaults to asynchronous Read Array, and the Status
Register is set to 0x80. Asserting RST# de-energizes all internal circuits, and places the output
drivers in High-Z. When RST# is asserted, the device shuts down the operation in progress, a
process which takes a minimum amount of time to complete. When RST# has been deasserted, the
device is reset to asynchronous Read Array state.
Note:
If RST# is asserted during a program or erase operation, the operation is terminated and the
memory contents at the aborted location (for a program) or block (for an erase) are no longer valid,
because the data may have been only partially written or erased.
When returning from a reset (RST# deasserted), a minimum wait is required before the initial read
access outputs valid data. Also, a minimum delay is required after a reset before a write cycle can
be initiated. After this wake
-
up interval passes, normal operation is restored. See
Section 7.0, “AC
Characteristics” on page 33
for details about signal-timing.
相關PDF資料 |
PDF描述 |
|---|---|
| PF48F0P0ZT00 | Circular Connector; Body Material:Aluminum; Series:PT00; No. of Contacts:41; Connector Shell Size:20; Connecting Termination:Crimp; Circular Shell Style:Wall Mount Receptacle; Circular Contact Gender:Socket; Insert Arrangement:20-41 |
| PF48F2P0ZT00 | Circular Connector; No. of Contacts:41; Series:; Body Material:Aluminum; Connector Shell Size:20; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:20-41 |
| PF48F3P0ZT00 | Intel StrataFlash Embedded Memory |
| PF48F4P0ZT00 | Circular Connector; No. of Contacts:21; Series:; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:22; Circular Contact Gender:Pin; Circular Shell Style:Wall Mount Receptacle; Insert Arrangement:22-21 |
| PF48F2000P0ZBQ0 | Intel StrataFlash Embedded Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PF48F5000M0Y1BEA | 制造商:Micron Technology Inc 功能描述:512BA/0S SCSP 1.8 X16D HF B1 ADMUX - Trays |
| PF48F6000M0Y0BEA | 制造商:Micron Technology Inc 功能描述:1024CP/0CP SCSP 1.8 X16D LF - Trays |
| PF48F6000M0Y0BHA | 制造商:Micron Technology Inc 功能描述:WIRELESS - Trays |
| PF48F6000M0Y1BHA | 制造商:Micron Technology Inc 功能描述:WIRELESS - Trays |
| PF48F6600M0U0BEA | 制造商:Micron Technology Inc 功能描述:1024CP/1024CP SCSP 1.8 X16D LF F1 VIRT-CE - Trays |
發布緊急采購，3分鐘左右您將得到回復。