- 您現在的位置：買賣IC網 > PDF目錄369960 > PDI1394P11 (NXP SEMICONDUCTORS) 3-port physical layer interface PDF資料下載
參數資料
| 型號： | PDI1394P11 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 網絡接口 |
| 英文描述： | 3-port physical layer interface |
| 中文描述： | DATACOM, INTERFACE CIRCUIT, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, SOT-314-2, LQFP-64 |
| 文件頁數： | 34/42頁 |
| 文件大?。?/td> | 233K |
| 代理商： | PDI1394P11 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Philips Semiconductors
Preliminary data
PDI1394P23
2-port/1-port 400 Mbps physical layer interface
2001 Sep 06
34
The sequence of events for resetting the PHY-LLC interface when it
is in the differentiated mode of operation (ISO terminal is low) is as
follows:
1. Normal operation. Interface is operating normally, with LPS
active, SYSCLK active, status and packet data reception and
transmission via the CTL and D lines, and request activity via
the LREQ line.
2. LPS deasserted. The LLC deasserts the LPS signal and, within
1.0 ms, terminates any request or interface bus activity, and
places its LREQ, CTL, and D outputs into a high-impedance
state (the LLC should terminate any output signal activity such
that signals end in a logic 0 state).
3. Interface reset. After T
LPS_RESET
time, the PHY determines that
LPS is inactive, terminates any interface bus activity, and places
its CTL and D outputs into a high-impedance state (the PHY will
terminate any output signal activity such that signals end in a
logic 0 state). The PHY-LLC interface is now in the reset state.
4. Interface restored. After the minimum T
RESTORE
time, the LLC
may again assert LPS active. (The minimum T
RESTORE
interval
provides sufficient time for the biasing networks used in Annex J
type isolation barrier circuits to stabilize and reach a quiescent
state if the isolation barrier has somehow become unbalanced.)
When LPS is asserted, the interface will be initialized as
described on the next page.
T
LPS_RESET
T
RESTORE
ISO
SYSCLK
CTL0, CTL1
D0 – D7
LREQ
LPS
(high)
(a)
(c)
(d)
(b)
SV01811
Figure 21.
Interface Reset, ISO High
相關PDF資料 |
PDF描述 |
|---|---|
| PDI1394P11BD | 3-port physical layer interface |
| PDI1394P25 | 1-port 400 Mbps physical layer interface |
| PDI1394P25BD | 1-port 400 Mbps physical layer interface |
| PDI1394P25EC | 1-port 400 Mbps physical layer interface |
| PDI1394P23BD | 2-port/1-port 400 Mbps physical layer interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDI1394P11A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-port physical layer interface |
| PDI1394P11ABD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-port physical layer interface |
| PDI1394P11ABD-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver |
| PDI1394P11BD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-port physical layer interface |
| PDI1394P11BD-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver |
發布緊急采購，3分鐘左右您將得到回復。