- 您現在的位置：買賣IC網 > PDF目錄369960 > PDI1394L41BE (NXP SEMICONDUCTORS) 8358 PBGA ENCRP NO-PB PDF資料下載
參數資料
| 型號： | PDI1394L41BE |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8358 PBGA ENCRP NO-PB |
| 中文描述： | 1 CHANNEL(S), 400M bps, LOCAL AREA NETWORK CONTROLLER, PQFP144 |
| 封裝： | PLASTIC, QFP-144 |
| 文件頁數： | 33/42頁 |
| 文件大?。?/td> | 233K |
| 代理商： | PDI1394L41BE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Philips Semiconductors
Preliminary data
PDI1394P23
2-port/1-port 400 Mbps physical layer interface
2001 Sep 06
33
Table 20. LPS Timing Parameters
PARAMETER
DESCRIPTION
MIN
MAX
UNIT
T
LPSL
T
LPSH
LPS low time (when pulsed) (see Note 1)
0.09
2.60
μ
S
LPS high time (when pulsed) (see Note 1)
0.021
2.60
μ
S
LPS duty cycle (when pulsed) (see Note 2)
20
55
%
T
LPS_RESET
T
LPS_DISABLE
T
RESTORE
T
CLK_ACTIVATE
Time for PHY to recognize LPS deasserted and reset the interface
2.60
2.68
μ
S
Time for PHY to recognize LPS deasserted and disable the interface
26.03
26.11
23
3
μ
S
Time to permit optional isolation circuits to restore during an interface reset
15
μ
S
Time for SYSCLK to be activated from reassertion of LPS
—
60
nS
NOTES:
1. The specified T
LPSL
and T
LPSH
times are worst–case values appropriate for operation with the PDI1394P23. These values are broader than
those specified for the same parameters in the P1394a Supplement (i.e., an implementation of LPS that meets the requirements of P1394a
will operate correctly with the PDI1394P23).
2. A pulsed LPS signal must have a duty cycle (ratio of T
to cycle period) in the specified range to ensure proper operation when using an
isolation barrier on the LPS signal (e.g., as shown in Figure 8)
3. The maximum value for T
does not apply when the PHY–LLC interface is disabled, in which case an indefinite time may elapse
before LPS is reasserted. Otherwise, in order to reset but not disable the interface it is necessary that the LLC ensure that LPS is
deasserted for less than T
LPS_DISABLE
.
The LLC requests that the interface be reset by deasserting the LPS
signal and terminating all bus and request activity. When the PHY
observes that LPS has been deasserted for T
LPS_RESET
, it resets
the interface. When the interface is in the reset state, the PHY sets
its CTL and D outputs in the logic 0 state and ignores any activity on
the LREQ signal. The timing for interface reset is shown in Figure 20
and Figure 21.
T
LPS_RESET
T
RESTORE
ISO
SYSCLK
CTL0, CTL1
D0 – D7
LREQ
LPS
(low)
(a)
(c)
(d)
(b)
T
LPSL
T
LPSH
SV01810
Figure 20.
Interface Reset, ISO Low
相關PDF資料 |
PDF描述 |
|---|---|
| PDI1394P21BE | 3-port physical layer interface |
| PDI1394P22BD | 3-port physical layer interface |
| PDI1394L11BA | 1394 AV link layer controller |
| PDI1394L21BE | 1394 full duplex AV link layer controller |
| PDI1394L21BP | 1394 full duplex AV link layer controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDI1394P11 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-port physical layer interface |
| PDI1394P11A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-port physical layer interface |
| PDI1394P11ABD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-port physical layer interface |
| PDI1394P11ABD-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver |
| PDI1394P11BD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-port physical layer interface |
發布緊急采購，3分鐘左右您將得到回復。