- 您現在的位置：買賣IC網 > PDF目錄369950 > PCK12429BD (NXP SEMICONDUCTORS) 25-400 MHz differential PECL clock generator PDF資料下載
參數資料
| 型號： | PCK12429BD |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | XO, clock |
| 英文描述： | 25-400 MHz differential PECL clock generator |
| 中文描述： | 400 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| 封裝： | LQFP-32 |
| 文件頁數： | 5/14頁 |
| 文件大?。?/td> | 128K |
| 代理商： | PCK12429BD |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
Philips Semiconductors
Product data
PCK12429
25–400 MHz differential PECL clock generator
2002 Jun 03
5
BLOCK DIAGRAM
XTAL1
SW00728
OSC
XTAL2
DIV 16
1 MHz
F
REF
PHASE
DETECTOR
VCO
9-BIT DIV M
COUNTER
LATCH
200–400
MHz
DIV N
(1, 2, 4, 8)
V
CC0
+3.3 V
LATCH
F
OUT
F
OUT
16 MHz
OE
0
1
0
1
LATCH
TEST
S_LOAD
P_LOAD
9-BIT
SR
2-BIT
SR
3-BIT
SR
S_DATA
S_CLOCK
V
CC1
+3.3 V
9
M[8:0]
2
N[1:0]
+3.3 V
PLL_V
CC
N[1:0]
Output Division
0 0
0 1
1 0
1 1
1
2
4
8
PROGRAMMING INTERFACE
Programming the device amounts to properly configuring the internal
dividers to produce the desired frequency at the outputs. The output
frequency can be represented by this formula:
F
OUT
= (F
XTAL
÷
16)
×
M
÷
N
(1)
Where F
XTAL
is the crystal frequency, M is the loop divider modulus,
and N is the output divider modulus. Note that it is possible to select
values of M such that the PLL is unable to achieve loop lock. To
avoid this, always make sure that M is selected to be 200
≤
M
≤
400
for a 16 MHz input reference.
Assuming that a 16 MHz reference frequency is used, the above
equation reduces to:
F
OUT
= M
÷
N
Substituting the four values for N (1, 2, 4, or 8) yields:
F
OUT
= M, F
OUT
= M
÷
2,
F
OUT
= M
÷
4 and F
OUT
= M
÷
8
for 200
≤
M
≤
400
The user can identify the proper M and N values for the desired
frequency from the above equations. The four output frequency
ranges established by N are 200–400 MHz, 100–200 MHz,
50–100 MHz, and 25–50 MHz respectively. From these ranges the
user will establish the value of N required, then the value of M can
be calculated based on the appropriate equation above. For
example, if an output frequency of 131 MHz was desired, the
following steps would be taken to identify the appropriate M and N
values. 131 MHz falls within the frequency range set by an N value
of 2 so N [1:0] = 01. For N = 2 F
OUT
= M
÷
2 and M = 2
×
F
OUT
.
Therefore, M = 131
×
2 = 262, so M[8:0] = 100000110. Following this
same procedure a user can generate any whole frequency desired
between 25 and 400 MHz. Note that for N
≥
2 fractional values of
F
OUT
can be realized. The size of the programmable frequency
steps (and thus the indicator of the fractional output frequencies
achievable) will be equal to F
XTAL
÷
16
÷
N.
For input reference frequencies other than 16 MHz, the set of
appropriate equations can be deduced from equation 1. For
computer applications another useful frequency base would be
16.666 MHz. From this reference, one can generate a family of
output frequencies at multiples of the 33.333 MHz PCI clock. As an
example, to generate a 133.333 MHz clock from a 16.666 MHz
reference, the following M and N values would be used:
F
OUT
= 16.666
÷
16
×
M
÷
N = 1.041625
×
M
÷
N
Let N = 2, M = 256,
F
OUT
= 1.041625
×
256
÷
2 = 133.328 MHz
The value for M falls within the constraints set for PLL stability,
therefore N[1:0] = 01 and M[8:0] = 100000000. If the value for M fell
outside of the valid range a different N value would be selected to try
to move M in the appropriate direction.
The M and N counters can be loaded either through a parallel or
serial interface. The parallel interface is controlled via the P_LOAD
signal such that a LOW to HIGH transition will latch the information
present on the M[8:0] and N[1:0] inputs into the M and N counters.
When the P_LOAD signal is LOW the input latches will be
transparent and any changes on the M[8:0] and N[1:0] inputs will
相關PDF資料 |
PDF描述 |
|---|---|
| PCK12429D | 25-400 MHz differential PECL clock generator |
| PCK2000MDB | CK97 66/100MHz Mobile System Clock Generator |
| PCK2001MDB | 14.318-150 MHz I2C 1:10 Clock Buffer |
| PCK2002M | 0-300 MHz I2C 1:10 clock buffer |
| PCK2002MDB | 0-300 MHz I2C 1:10 clock buffer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCK12429BD,118 | 功能描述:時鐘發生器及支持產品 25-400MHZ DIFF PECL RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| PCK12429BD,151 | 功能描述:時鐘發生器及支持產品 25-400MHZ DIFF PECL RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| PCK12429BD,157 | 功能描述:時鐘發生器及支持產品 25-400MHZ DIFF PECL RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| PCK12429BD-S | 功能描述:時鐘發生器及支持產品 25-400MHZ DIFF PECL CLOCK GEN RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| PCK12429BD-T | 功能描述:時鐘發生器及支持產品 25-400MHZ DIFF PECL CLOCK GEN RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
發布緊急采購，3分鐘左右您將得到回復。