參數資料
型號： PCA9671
廠商： NXP Semiconductors N.V.
英文描述： Remote 16-bit I/O expander for Fm+ I2C-bus with reset
中文描述： 遠程16位I / O擴展調頻的I2C總線與復位
文件頁數： 9/34頁
文件大?。?/td> 183K
代理商： PCA9671
PCA9671_1
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 01 — 20 December 2006
9 of 34
NXP Semiconductors
PCA9671
Remote 16-bit I/O expander for Fm+ I
2
C-bus with reset
7.2 Software Reset call, and device ID addresses
Two other different addresses can be sent to the PCA9671.
General Call address: allows to reset the PCA9671 through the I
2
C-bus upon
reception of the right I
2
C-bus sequence. See
Section 7.2.1 “Software Reset”
for more
information.
Device ID address: allows to read ID information from the device (manufacturer, part
identification, revision). See
Section 7.2.2 “Device ID (PCA9671 ID field)”
for more
information.
7.2.1
Software Reset
The Software Reset Call allows all the devices in the I
2
C-bus to be reset to the power-up
state value through a specific formatted I
2
C-bus command. To be performed correctly, it
implies that the I
2
C-bus is functional and that there is no device hanging the bus.
The Software Reset sequence is defined as following:
1. A START command is sent by the I
2
C-bus master.
2. The reserved General Call I
2
C-bus address ‘0000 000’ with the R/W bit set to logic 0
(write) is sent by the I
2
C-bus master.
3. The PCA9671 device(s) acknowledge(s) after seeing the General Call address
‘0000 0000’ (00h) only. If the R/W bit is set to logic 1 (read), no acknowledge is
returned to the I
2
C-bus master.
4. Once the General Call address has been sent and acknowledged, the master sends
1 byte. The value of the byte must be equal to 06h.
a. The PCA9671 acknowledges this value only. If the byte is not equal to 06h, the
PCA9671 does not acknowledge it.
If more than 1 byte of data is sent, the PCA9671 does not acknowledge any more.
5. Once the right byte has been sent and correctly acknowledged, the master sends a
STOP command to end the Software Reset sequence: the PCA9671 then resets to
the default value (power-up value) and is ready to be addressed again within the
specified bus free time. If the master sends a Repeated START instead, no reset is
performed.
Fig 10. General Call address
Fig 11. Device ID address
0
002aac155
0
0
0
0
0
0
0
R/W
R/W
002aab638
1
1
1
1
1
0
0
相關PDF資料
PDF描述
PCA9671DB Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9671DK Remote 16-bit I/O expander for Fm+ I2C-bus with reset
PCA9673 Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
PCA9673DB Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
PCA9673DK Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt and reset
相關代理商/技術參數
參數描述
PCA9671BQ,118 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671BQ-T 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO FM+I2C-RESET RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671BS,118 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671BS-T 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO FM+I2C-RESET RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671D 功能描述:接口-I/O擴展器 16-BIT I2C FM+ QB GPIO RST PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*