參數資料
| 型號： | PCA9574PW,112 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 6/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 8B 16TSSOP |
| 標準包裝： | 96 |
| 接口： | I²C，SM 總線 |
| 輸入/輸出數： | 8 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 1.1 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
| 包括： | POR |
| 其它名稱： | 935285149112 PCA9574PW PCA9574PW-ND |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
PCA9574
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 4 — 25 April 2012
14 of 33
NXP Semiconductors
PCA9574
8-bit I2C-bus and SMBus, level translating, low volage GPIO
8.
Characteristics of the I2C-bus
The I2C-bus is for 2-way, 2-line communication between different ICs or modules. The two
lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be
connected to a positive supply via a pull-up resistor when connected to the output stages
of a device. Data transfer may be initiated only when the bus is not busy.
8.1 Bit transfer
One data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the HIGH period of the clock pulse as changes in the data line at this time
will be interpreted as control signals (see Figure 8).
8.1.1 START and STOP conditions
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW
transition of the data line while the clock is HIGH is defined as the START condition (S). A
LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP
condition (P) (see Figure 9).
8.2 System configuration
A device generating a message is a ‘transmitter’; a device receiving is the ‘receiver’. The
device that controls the message is the ‘master’ and the devices which are controlled by
the master are the ‘slaves’ (see Figure 10).
Fig 8.
Bit transfer
mba607
data line
stable;
data valid
change
of data
allowed
SDA
SCL
Fig 9.
Definition of START and STOP conditions
mba608
SDA
SCL
P
STOP condition
S
START condition
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9574PW,118 | IC I/O EXPANDER I2C 8B 16TSSOP |
| 2-964577-2 | MULTIFIT RAHMEN 2P |
| 1-964577-5 | MULTIFIT RAHMEN 5P |
| 1-964576-3 | PCB RAHMEN 13P |
| PCA8574TS,118 | IC I/O EXPANDER I2C 8B 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9574PW-T | 功能描述:轉換 - 電壓電平 8-BIT I2C-BUS/SMBUS GPIO TRANS RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| PCA9575HF,118 | 功能描述:I2C 接口集成電路 16-BIT I2C-BUS SMBus LW Voltage GPIO RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| PCA9575HF118 | 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| PCA9575PW1,118 | 功能描述:I2C 接口集成電路 I2C Bus/ SMBus Level Translating 24-Pin RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| PCA9575PW2,118 | 功能描述:I2C 接口集成電路 I2C Bus/ SMBus Level Translating 28-Pin RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
發(fā)布緊急采購，3分鐘左右您將得到回復。