- 您現在的位置：買賣IC網 > PDF目錄369944 > P89LPC9103 (NXP Semiconductors N.V.) 8-bit microcontrollers with two-clock accelerated 80C51 core 1 kB 3 V byte-erasable Flash with 8-bit A/D converter PDF資料下載
參數資料
| 型號： | P89LPC9103 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-bit microcontrollers with two-clock accelerated 80C51 core 1 kB 3 V byte-erasable Flash with 8-bit A/D converter |
| 中文描述： | 8位微控制器兩個小時加速80C51的核心具有1KB 3伏字節可擦除閃存的8位A / D轉換器 |
| 文件頁數： | 32/58頁 |
| 文件大?。?/td> | 257K |
| 代理商： | P89LPC9103 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
9397 750 14655
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 11 April 2005
32 of 58
Philips Semiconductors
P89LPC9102/9103/9107
8-bit microcontrollers with two-clock accelerated 80C51 core
After power-up all I/O pins, except P1.5, may be configured by software.
Pin P1.5 is input-only.
Every output on the P89LPC9102/9103/9107 has been designed to sink typical LED drive
current. However, there is a maximum total output current for all ports which must not be
exceeded. Please refer to
Table 12 “Static characteristics”
for detailed specifications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
8.13 Power monitoring functions
The P89LPC9102/9103/9107 incorporates power monitoring functions designed to
prevent incorrect operation during initial power-up and power loss or reduction during
operation. This is accomplished with two hardware functions: Power-on Detect and
Brownout detect.
8.13.1
Brownout detection
The Brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a Brownout detection to cause a processor reset,
however, it may alternatively be configured to generate an interrupt.
Brownout detection may be enabled or disabled in software.
If Brownout detection is enabled, the brownout condition occurs when V
DD
falls below the
brownout trip voltage, V
BO
(see
Table 12 “Static characteristics”
), and is negated when
V
DD
rises above V
BO
. If the P89LPC9102/9103/9107 device is to operate with a power
supply that can be below 2.7 V, Brownout detect Enable (BOE) should be left in the
unprogrammed state so that the device can operate at 2.4 V, otherwise continuous
brownout reset may prevent the device from operating.
For correct activation of Brownout detect, the V
DD
rise and fall times must be observed.
Please see
Table 12 “Static characteristics”
for specifications.
8.13.2
Power-on detection
The Power-on Detect has a function similar to the Brownout detect, but is designed to
work as power comes up initially, before the power supply voltage reaches a level where
Brownout detect can work. The Power-on detect flag (POF) in the RSTSRC register is set
to indicate an initial power-up condition. The POF flag will remain set until cleared by
software.
8.14 Power reduction modes
The P89LPC9102/9103/9107 supports three different power reduction modes. These
modes are Idle mode, Power-down mode, and Total Power-down mode.
8.14.1
Idle mode
Idle mode leaves peripherals running in order to allow them to activate the processor
when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle
mode.
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC9103FTK | 8-bit microcontrollers with two-clock accelerated 80C51 core 1 kB 3 V byte-erasable Flash with 8-bit A/D converter |
| P89LPC915 | 8-bit microcontrollers with accelerated two-clock 80C51 core 2 kB 3 V Flash with 8-bit A/D converter |
| P89LPC915HDH | 8-bit microcontrollers with accelerated two-clock 80C51 core 2 kB 3 V Flash with 8-bit A/D converter |
| P89LPC916 | 8-bit microcontrollers with accelerated two-clock 80C51 core 2 kB 3 V Flash with 8-bit A/D converter |
| P89LPC917 | 8-bit microcontrollers with accelerated two-clock 80C51 core 2 kB 3 V Flash with 8-bit A/D converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC9103FTK | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 1K FLASH HVSON-10 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 1K FLASH, HVSON-10 |
| P89LPC9103FTK,115 | 功能描述:8位微控制器 -MCU 80C51 1K FL 128B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC9107 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock accelerated 80C51 core 1 kB 3 V byte-erasable flash with 8-bit A/D converter |
| P89LPC9107FDH | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 1K FLASH TSSOP14 |
| P89LPC9107FDH,129 | 功能描述:8位微控制器 -MCU 80C51 1K FL 128B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。