參數資料
型號: P87C055
廠商: NXP Semiconductors N.V.
英文描述: Microcontrollers for TV and video MTV
中文描述: 電視和視頻微控制器MTV
文件頁數: 26/40頁
文件大?。?/td> 243K
代理商: P87C055
1996 Mar 22
26
Philips Semiconductors
Product specification
Microcontrollers for TV and video (MTV)
83C145; 83C845
83C055; 87C055
14 PROGRAMMING CONSIDERATIONS
14.1
EPROM Characteristics
The 87C055 is programmed by using a modified Quick-Pulse Programming algorithm similar to that used for devices
such as the 87C751. It differs from these devices in that a serial data stream is used to place the 87C055 in the
programming mode.
Figure 9 shows a block diagram of the programming configuration for the 87C055.
Table 31
Pin usage for Programming
Note
1.
Multiplexing of these address components is performed using the ASEL input:
a) ASEL input is driven HIGH and then drive Port 2 with the high-order bits of the address. ASEL should remain
HIGH for at least 13 clock cycles.
b) ASEL may then be driven LOW which latches the high-order bits of the address internally. The high-order address
should remain on Port 2 for at least 2 clock cycles after ASEL is driven LOW.
c) Port 2 may then be driven with the low byte of the address. The low-order address will be internally stable 13 clock
cycles later. The address will remain stable provided that the low byte placed on Port 2 is held stable and ASEL
is kept LOW.
d) ASEL needs to be pulsed HIGH only to change the high byte of the address.
PIN
USAGE
XTAL1
Oscillator input and receives the master system clock. This clock should be between
1.2 and 6 MHz.
Used to accept the serial data stream that places the 87C055 into various programming modes.
This pattern consists of a 10-bit code with the LSB sent first. Each bit is synchronized to the
clock input, XTAL1.
RESET
Port 0
V
PP
/TDAC/P0.0
PROG/PWM1/P0.1 Used as the program PROG signal. This pin is used for the 25 programming pulses.
Used as the programming voltage supply input (V
PP
signal).
Port 2
P2.7 to P2.0
Address input for the byte to be programmed and accepts both the high- and low-order
components of the 11-bit address; note 1.
Port 3
P3.7 to P3.0
Used as a bidirectional data bus during programming and verify operations. During programming
mode, it accepts the byte to be programmed. During verify mode, it provides the contents of the
EPROM location specified by the address which has been supplied to Port 2.
相關PDF資料
PDF描述
P87C055BBP Microcontrollers for TV and video MTV
P83C055BBP Microcontrollers for TV and video MTV
P83C145BBP MICRO 21 F SOD
P83C851FBA CMOS single-chip 8-bit microcontroller with on-chip EEPROM
P80C851IBA CMOS single-chip 8-bit microcontroller with on-chip EEPROM
相關代理商/技術參數
參數描述
P87C055BBNB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
P87C055BBP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Microcontrollers for TV and video MTV
P87C151SA 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:HIGH-PERFORMANCE CHMOS MICROCONTROLLER
P87C151SB 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:HIGH-PERFORMANCE CHMOS MICROCONTROLLER
P87C251SA16 功能描述:IC MCU 8-BIT 8K 16MHZ OTP 40-DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:87C 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C,IrDA,LIN,SPI,UART/USART 外圍設備:DMA,PDR,POR,PVD,PWM,溫度傳感器,WDT 輸入/輸出數:26 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN,36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND