參數資料
型號： P83C591VFA
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： Single-chip 8-bit microcontroller with CAN controller
中文描述： 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC44
封裝： PLASTIC, MO-047AC, SOT-187-2, LCC-44
文件頁數： 34/161頁
文件大?。?/td> 588K
代理商： P83C591VFA
1999 Aug 19
34
Philips Semiconductors
Objective Specification
Single-chip 8-bit microcontroller with CAN controller
P8xC591
12.5.2
M
ODE
R
EGISTER
(MOD)
The contents of the Mode Register are used to change the behaviour of the CAN Controller. Bits may be set or reset by
the CPU that uses the Mode Register as a read / write memory. Reserved Bits are read as “0”.
Table 13
Mode Register (MOD) CAN Addr. 0 bit interpretation
Notes
1.
A write access to the bits MOD.1, MOD.2, MOD.5, MOD.6 and MOD.7 is possible only, if the Reset Mode is entered
previously.
The PeliCAN Block will enter Sleep Mode, if the Sleep Mode bit is set ‘1’ (sleep), there is no bus activity and no
interrupt is pending. Setting of SM with at least one of the previously mentioned exceptions valid will result in a
wake-up interrupt. The CAN block will wake up if SM is set LOW (wake-up) or there is bus activity. On wake-up, a
Wake-up Interrupt is generated. A sleeping CAN block which wakes up due to bus activity will not be able to receive
this message until it detects 11 consecutive recessive bits (Bus-Free sequence). Note that setting of SM is not
possible in Reset Mode. After clearing of Reset Mode, setting of SM is possible first, when Bus-Free is detected
again.
2.
BIT
SYMBOL
NAME
VALUE
FUNCTION
MOD.7
TM
Test Mode;
Note 1
1 (activated)
The TX0 pin will reflect the bit, detected on RX pin, with the
next positive edge of the system clock. TN0 and TP0 are
configured according the setting of OCR. The TXDC output
directly reflects RXDC. The RPM bit has no influence within
this mode.
0 (disabled)
1 (high active)
MOD.6
MOD.5
RIPM
RPM
Reserved.
Receive Polarity
Mode
RXD inputs are active high (dominant = 1).
0 (low active)
1 (high active)) The PeliCAN Block enters Sleep Mode if no CAN interrupt is
pending and there is no bus activity.
0 (low active)
1 (self test)
In this mode a full node test is possible without any other
active node on the bus using the Self Reception Request
command. The CAN Controller will perform a successful
transmission, even if there is no acknowledge received.
0 (normal)
An acknowledge is required for successful transmission.
1 (reset)
In this mode the CAN would give no acknowledge to the
CAN bus, even if a message is received successfully. No
active error flags are driven to the bus. The error counters
are stopped at the current value.
0 (normal)
Normal communication.
1 (reset)
Setting the Reset Mode bit results in aborting the current
transmission/reception of a message and entering the Reset
Mode.
0 (normal)
On the’1’-to-’0’ transition of the Reset Mode bit, the CAN
Controller returns to the Operating Mode.
RXD inputs are active low (dominant = 0).
MOD.4
SM
Sleep Mode;
Note 2
MOD.3
MOD.2
reserved
Self Test Mode;
Note 1
STM
MOD.1
LOM
Listen Only
Mode; Notes 1
and 3
MOD.0
RM
Reset Mode;
Note 4
相關PDF資料
PDF描述
P80CE560 8-BIT SINGLE CHIP MICROCONTROLLERS
P87CE560EFB BATTERY CHG UNIV 12VDC @ 500MA
P83CE560 8-BIT SINGLE CHIP MICROCONTROLLERS
P87CE560 8-BIT SINGLE CHIP MICROCONTROLLERS
P80CE560EFB 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
P83C591VFB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller with CAN controller
P83C592 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN
P83C592FFA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN
P83C592FHA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN
P83C652EBA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*