參數資料
型號： OM13006,598
廠商： NXP Semiconductors
文件頁數： 3/51頁
文件大?。?/td> 0K
描述： BOARD EVAL EM773 METER EU PLUG
其它有關文件： EM773 Energy Metering IC Training
設計資源： Plug Meter Schematics, Gerber Files
USB Dongle Schematics, Gerber Files
標準包裝： 1
主要目的： 電源管理，電度表/功率表
嵌入式： 是，MCU，32 位
已用 IC / 零件： EM773FHN33，551
已供物品： 板
相關產品： 568-5213-ND - IC ENERGY METER ARM 32VQFN
其它名稱： 568-6681
EM773
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 2 — 3 January 2012
11 of 51
NXP Semiconductors
EM773
Energy metering IC
Four programmable interrupt priority levels with hardware priority level masking.
Software interrupt generation.
7.5.2 Interrupt sources
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any GPIO pin (total of up to 25 pins) regardless of the selected function, can be
programmed to generate an interrupt on a level, or rising edge or falling edge, or both.
7.6 IOCONFIG block
The IOCONFIG block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
7.7 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
The EM773 uses accelerated GPIO functions:
GPIO registers are a dedicated AHB peripheral so that the fastest possible I/O timing
can be achieved.
Entire port value can be written in one instruction.
Additionally, any GPIO pin (total of up to 25 pins) providing a digital function can be
programmed to generate an interrupt on a level, a rising or falling edge, or both.
7.7.1 Features
Bit level port registers allow a single instruction to set or clear any number of bits in
one write operation.
Direction control of individual bits.
All I/O default to inputs with pull-ups enabled after reset with the exception of the
I2C-bus pins PIO0_4 and PIO0_5.
Pull-up/pull-down resistor configuration can be programmed through the IOCONFIG
block for each GPIO pin (except for pins PIO0_4 and PIO0_5).
All GPIO pins (except PIO0_4 and PIO0_5) are pulled up to 3.3 V (VDD = 3.3 V) if their
pull-up resistor is enabled in the IOCONFIG block.
Programmable open-drain mode.
相關PDF資料
PDF描述
CM252016-680KL INDUCTOR CHIP 68UH 2520 SMD
ECM25DRXN CONN EDGECARD 50POS DIP .156 SLD
VI-J4P-EX CONVERTER MOD DC/DC 13.8V 75W
SI5319-EVB BOARD EVALUATION SI5319
EMM11DSEN-S243 CONN EDGECARD 22POS .156 EYELET
相關代理商/技術參數
參數描述
OM13007 制造商:NXP Semiconductors 功能描述:KIT DEV FOR MPT612 制造商:NXP Semiconductors 功能描述:DEV KIT, FOR MPT612 制造商:NXP Semiconductors 功能描述:DEV KIT, FOR MPT612; SVHC:No SVHC (19-Dec-2012); Kit Features:Low Power High Performance, High Value, LPC1102, with 32KB Of Flash, 8KB of RAM; MCU Supported Families:MPT612
OM13007,598 功能描述:開發板和工具包 - ARM MPT612 IC REFERENCE BOARD RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
OM13008 制造商:NXP Semiconductors 功能描述:LPC1227, LPCXPRESSO, DEV BOARD 制造商:NXP Semiconductors 功能描述:LPCXpresso Board for LPC1200 Series Development Board 制造商:NXP Semiconductors 功能描述:LPCXpresso Board for LPC1200 Low-Cost Development Board ARM Cortex-M0 MCU 制造商:NXP Semiconductors 功能描述:LPC1227, LPCXPRESSO, DEV BOARD; Silicon Manufacturer:NXP; Core Architecture:ARM; Core Sub-Architecture:Cortex-M0; Silicon Core Number:LPC12xx; Silicon Family Name:LPC122X; Features:Development Board for LPC122X Microcontroller; ;RoHS Compliant: Yes 制造商:NXP 功能描述:LPCXpresso Board for LPC1200 Low-Cost Development Board ARM Cortex-M0 MCU
OM13008, 598 制造商:NXP Semiconductors 功能描述:
OM13008,598 功能描述:開發板和工具包 - ARM LPCXpresso Board RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*