- 您現在的位置：買賣IC網 > PDF目錄224618 > NX25P16-VSI (WINBOND ELECTRONICS CORP) 16M X 1 FLASH 2.7V PROM, PDSO8 PDF資料下載
參數資料
| 型號： | NX25P16-VSI |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 16M X 1 FLASH 2.7V PROM, PDSO8 |
| 封裝： | 0.208 INCH, SOIC-8 |
| 文件頁數： | 16/43頁 |
| 文件大?。?/td> | 918K |
| 代理商： | NX25P16-VSI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
W25P80 / W25P16 / W25P32
Publication Release Date: December 11, 2005
- 23 -
Revision J
9.2.11 Power-down (B9h)
Although the standby current during normal operation is relatively low, standby current can be further
reduced with the Power-down instruction. The lower power consumption makes the Power-down
instruction especially useful for battery powered applications (See ICC1 and ICC2 in AC
Characteristics). The instruction is initiated by driving the /CS pin low and shifting the instruction code
“B9h” as shown in figure 13.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Power-
down instruction will not be executed. After /CS is driven high, the power-down state will entered
within the time duration of tDP (See AC Characteristics). While in the power-down state only the
Release from Power-down / Device ID instruction, which restores the device to normal operation, will
be recognized. All other instructions are ignored. This includes the Read Status Register instruction,
which is always available during normal operation. Ignoring all but one instruction makes the Power
Down state a useful condition for securing maximum write protection. The device always powers-up in
the normal operation with the standby current of ICC1.
Figure 13. Deep Power-down Instruction Sequence Diagram
9.2.12 Release Power-down / Device ID (ABh)
The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to
release the device from the power-down state, obtain the devices electronic identification (ID) number
or do both.
When used only to release the device from the power-down state, the instruction is issued by driving
the /CS pin low, shifting the instruction code “ABh” and driving /CS high as shown in figure 14. After
the time duration of tRES1 (See AC Characteristics) the device will resume normal operation and other
instructions will be accepted. The /CS pin must remain high during the tRES1 time duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated
by driving the /CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The
Device ID bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as
shown in figure 15. The Device ID values for the W25P80, W25P16 and W25P32 are listed in
Manufacturer and Device Identification table. The Device ID can be read continuously. The instruction
is completed by driving /CS high.
相關PDF資料 |
PDF描述 |
|---|---|
| NX3225SA-100.000M-STD-CSR-3 | QUARTZ CRYSTAL RESONATOR, 100 MHz |
| NX5A0AE01 | MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| NX5B0AE01 | MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| NX5C0AE01 | MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
| NX5G0AE01 | MALE, STRAIGHT TWO PART BOARD CONNECTOR, PRESS FIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NX25P20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1M BIT 2M BIT AND 4M BIT SERIAL FLASH MEMORY WITH 10MHZ SPI |
| NX25P40 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1M BIT 2M BIT AND 4M BIT SERIAL FLASH MEMORY WITH 10MHZ SPI |
| NX-25TA-CV1 | 制造商:HRS 制造商全稱:HRS 功能描述:I/O Card Interface Connectors |
| NX-25TA-CV1(50) | 功能描述:記憶卡連接器 PC CARD FRAME KIT ACCESRY PLUG CVR RoHS:否 制造商:Yamaichi Electronics 產品:Card Connectors 卡類型:microSD 類型: 節距: 方向: 安裝風格:SMD/SMT 端接類型: 排數: 觸點數量: 電流額定值:0.5 A 電壓額定值:50 V |
| NX-25T-BS | 制造商:Hirose 功能描述:234-0074-0-00 EACH |
發布緊急采購，3分鐘左右您將得到回復。