參數資料
型號： NT6828
廠商： Electronic Theatre Controls, Inc.
英文描述： I2C Bus Controlled On-Screen Display
中文描述： I2C總線控制屏幕顯示
文件頁數： 19/31頁
文件大?。?/td> 1846K
代理商： NT6828
NT6828
19
3. I
2
C Bus Communication:
The relative figure shows the I2C Bus transmission format. The master initiates a transmission routine by generating a
START condition, followed by a slave address byte. Once the address is properly identified, the slave will respond with an
ACKNOWLEDGE signal by pulling the SDA line LOW during the ninth SCL clock. Each data byte which then follows must be
eight bits long, plus the ACKNOWLEDGE bit, which makes up nine bits all together. Appropriate row and column address
information and display data can be downloaded sequentially in one of the three transmission formats described in Figure
“Access Register Operation”. In the cases of no ACKNOWLEDGE or completion of data transfer, the master will generate a
STOP condition to terminate the transmission routine. Note that the OSD_EN bit must be set after all the display information
has been sent in order to activate the displaying circuitry of NT6828, so that the received information can then be displayed.
(1) Access the Display Control Registers:
After proper identification by the receiving device, the data train of arbitrary length is transmitted from the master. There are
three transmission formats from (a) to (c) as referred to Figure 9 & Table 8. The data train in each sequence consists of row
addresses, column addresses, and data. In format (a), data must be preceded with the corresponding row address and
column address. This format is particularly suitable for updating small amounts of data between different rows. However, if
the current information byte has the same row address as the one before, format (b) is recommended. For a full screen
pattern change (which requires a massive information update), or during a power-on situation, most of the row and column
addresses on either (a) or (b) format will appear to be redundant. A more efficient data transmission format (c) should be
applied. This sends the starting row and column addresses once only, and then treats all subsequent data as display
information. The row and column addresses will be automatically incremented internally for each display information data
from the starting location.
To differentiate the row and column addresses when transferring data from master, the MSB (Most Significant Bit) is set as
in Table Transmission: ‘1’ represents row, while ‘0’ represents column address. Furthermore, to distinguish the column
address between format (a), (b) and (c); the sixth bit of the column address is set to ‘1’, which represents format (c), and a ‘0’
for format (a) or (b). There is some limitation when using mix-formats during a single transmission. It is permissible to change
the format from (a) to (b), or from (a) to (c), or from (b) to (a), but not from (c) back to (a) or (b).
(2) Access the RAM Fonts Area:
There are some differences when accessing the RAM font. One font consists of 18 rows and 12 columns of dot matrix. At
each row of one font, there are 18 bits of data which allocates 2 bytes of control data with 4 unavailable bits. Thus, each font
occupies 36 bytes of control data. From the memory map of RAM fonts, font0 is allocated at row 0 & column 0 - 35, and
font1, row 1 & column 0 ~ 35, etc. (Please refer to Figure 9.)
Table 8. Address Data Transmission for Registers
ITEM
No
ADDRESS
B7
B6
B5
B4
B3
B2
B1
B0
Type
1
Row
1
0
0
X
D
D
D
D
(a), (b), (c)
2
Column
0
0
X
D
D
D
D
D
(a), (b)
Display Register
3
Column
0
1
X
D
D
D
D
D
(c)
4
Row
1
0
1
X
D
D
D
D
(a), (b), (c)
5
Column
0
0
X
D
D
D
D
D
(a), (b)
Attribute / Control
Register
6
Column
0
1
X
D
D
D
D
D
(c)
7
Row
1
1
X
X
X
D
D
D
(a), (b), (c)
8
Column
0
0
D
D
D
D
D
D
(a), (b)
RAM Fonts
9
Column
0
1
D
D
D
D
D
D
(c)
相關PDF資料
PDF描述
NT6828K I2C Bus Controlled On-Screen Display
NT6861U 8-Bit Microcontroller for Monitor
NT6861 8-Bit Microcontroller for Monitor
NT6862 8-Bit Microcontroller for Monitor
NT6862U 8-Bit Microcontroller for Monitor
相關代理商/技術參數
參數描述
NT6828K 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Bus Controlled On-Screen Display
NT68520EF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:XGA,SXGA Flat Panel Monitor Controller
NT68520XF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:XGA,SXGA Flat Panel Monitor Controller
NT6861 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller for Monitor
NT6861U 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller for Monitor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*