- 您現在的位置：買賣IC網 > PDF目錄9924 > NCV7356D2R2G (ON Semiconductor)IC TXRX CAN SGL WIRE 14-SOIC PDF資料下載
參數資料
| 型號： | NCV7356D2R2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 23/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX CAN SGL WIRE 14-SOIC |
| 標準包裝： | 1 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CAN |
| 電源電壓： | 5 V ~ 27 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOICN |
| 包裝： | 剪切帶 (CT) |
| 其它名稱： | NCV7356D2R2GOSCT |
NCV7356
http://onsemi.com
8
TIMING MEASUREMENT LOAD CONDITIONS
Normal and High Voltage WakeUp Mode
HighSpeed Mode
min load / min tau
3.3 kW / 540 pF
Additional 140 W tool resistance
to ground in parallel
min load / max tau
3.3 kW / 1.2 nF
max load / min tau
200 W / 5.0 nF
Additional 120 W tool resistance
to ground in parallel
max load / max tau
200 W / 20 nF
ELECTRICAL CHARACTERISTICS (5.0 V ≤ VBAT ≤ 27 V, 40°C ≤ TA ≤ 125°C, unless otherwise specified.)
Characteristic
Symbol
Condition
Min
Typ
Max
Unit
Transmit Delay in Normal and WakeUp Mode,
Bus Rising Edge (Notes 12, 13)
tTr
Min and Max Loads per Timing
Measurement Load Conditions
2.0
6.3
ms
Transmit Delay in WakeUp Mode to VihWU,
Bus Rising Edge (Notes 12, 14)
tTWUr
Min and Max Loads per Timing
Measurement Load Conditions
2.0
18
ms
Transmit Delay in Normal Mode,
tTf
Min and Max Loads per Timing
Measurement Load Conditions
1.8
10
ms
Transmit Delay in WakeUp Mode,
tTWU1f
Min and Max Loads per Timing
Measurement Load Conditions
3.0
13.7
ms
Transmit Delay in HighSpeed Mode,
Bus Rising Edge (Notes 12, 17)
tTHSr
Min and Max Loads per Timing
Measurement Load Conditions
0.1
1.5
ms
Transmit Delay in HighSpeed Mode,
tTHSf
Min and Max Loads per Timing
Measurement Load Conditions
0.04
3.0
ms
Receive Delay, All Active Modes (Note 19)
tDR
CANH High to Low Transition
0.3
1.0
ms
Receive Delay, All Active Modes (Note 19)
tRD
CANH Low to High Transition
0.3
1.0
ms
Input Minimum Pulse Length,
All Active Modes (Note 17)
tmpDR
tmpRD
CANH High to Low Transition
CANH Low to High Transition
0.1
1.0
ms
WakeUp Filter Time Delay
tWUF
See Figure 4
10
70
ms
Receive Blanking Time, After
TxD LH Transition
trb
See Figure 5
0.5
6.0
ms
TxD Timeout Reaction Time
ttout
Normal and HighSpeed Mode
17
ms
TxD Timeout Reaction Time
ttoutwu
WakeUp Mode
17
ms
Delay from Normal to HighSpeed and
High Voltage WakeUp Mode
tdnhs
30
ms
Delay from HighSpeed and High Voltage
WakeUp to Normal Mode
tdhsn
30
ms
Delay from Normal to Standby Mode
tdsby
VBAT = 6.0 V to 27 V
500
ms
Delay from Sleep to Normal Mode
tdsnwu
VBAT = 6.0 V to 27 V
50
ms
Delay from Sleep to High Voltage Mode
tdshv
VBAT = 6.0 V to 27 V
50
ms
Delay from Standby to Sleep Mode (Note 20)
tdsleep
VBAT = 6.0 V to 27 V
100
250
500
ms
12.Minimum signal delay time is measured from the TxD voltage threshold to CANH = 1.0 V. t load should be min per the Timing Measurement
Load Conditions table.
13.Maximum signal delay time is measured from the TxD voltage threshold to CANH = 3.5 V at VBAT = 27 V, CANH = 2.8 V at VBAT = 5.0 V. t load
should be max per the Timing Measurement Load Conditions table.
14.Maximum signal delay time is measured from the TxD voltage threshold to CANH = 9.2 V. Vihwumax = Vihwufix,
max + Vgoff = 7.9 V + 1.3 V = 9.2 V. t load should be max per the Timing Measurement Load Conditions table.
15.Minimum signal delay time is measured from the TxD voltage threshold to CANH = 3.5 V at VBAT = 27 V, CANH = 2.8 V at VBAT = 5.0 V. t load
should be min per the Timing Measurement Load Conditions table.
16.Maximum signal delay time is measured from the TxD voltage threshold to CANH = 1 V. t load should be max per the Timing Measurement
Load Conditions table.
17.Maximum signal delay time is measured from the TxD voltage threshold to CANH = 3.5 V. t load should be max per the Timing Measurement
Load Conditions table.
18.Minimum signal delay time is measured from the TxD voltage threshold to CANH = 3.5 V. t load should be min per the Timing Measurement
Load Conditions table.
19.Receive delay time is measured from the rising / falling edge crossing of the nominal Vih value on CANH to the falling (Vcmos_il_max) / rising
(Vcmos_ih_min) edge of RxD. This parameter is tested by applying a square wave signal to CANH. The minimum slew rate for the bus rising
and falling edges is 50 V/ms. The low level on bus is always 0 V. For normal mode and highspeed mode testing the high level on bus is 4 V.
For HVWU mode testing the high level on bus is VBAT 2 V. Relaxation of this noncritical parameter from 0.15 ms to 0.10 ms may be addressed
in future revisions of GMW3089.
20.Tested on 14 Pin package only.
相關PDF資料 |
PDF描述 |
|---|---|
| ICL3232EIBNZ | IC 2DRVR/2RCVR RS232 3V 16-SOIC |
| IDT72V2103L15PFG8 | IC FIFO SUPERSYNCII 15NS 80-TQFP |
| MAX1083BEUE+T | IC ADC 10BIT 300KSPS 16-TSSOP |
| IDT72V2103L15PF8 | IC FIFO SUPERSYNCII 15NS 80-TQFP |
| MS27656T15F15PD | CONN RCPT 15POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV7356DR2 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Single Wire CAN Transceiver |
| NCV7361 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Voltage Regulator with Integrated LIN Transceiver |
| NCV7361A | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Voltage Regulator with Integrated LIN Transceiver |
| NCV7361A_05 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Voltage Regulator with Integrated LIN Transceiver |
| NCV7361AD | 功能描述:低壓差穩壓器 - LDO LDO REG w/Integrated RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。