- 您現在的位置：買賣IC網 > PDF目錄363233 > NCV33035DWR2 (ON SEMICONDUCTOR) Brushless DC Motor Controller PDF資料下載
參數資料
| 型號： | NCV33035DWR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | Brushless DC Motor Controller |
| 中文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.1 A, PDSO24 |
| 封裝： | PLASTIC, SOP-24 |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 430K |
| 代理商： | NCV33035DWR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MC33035, NCV33035
http://onsemi.com
9
INTRODUCTION
The MC33035 is one of a series of high performance
monolithic DC brushless motor controllers produced by
Motorola. It contains all of the functions required to
implement a fullfeatured, open loop, three or four phase
motor control system. In addition, the controller can be made
to operate DC brush motors. Constructed with Bipolar
Analog technology, it offers a high degree of performance and
ruggedness in hostile industrial environments. The MC33035
contains a rotor position decoder for proper commutation
sequencing, a temperature compensated reference capable of
supplying a sensor power, a frequency programmable
sawtooth oscillator, a fully accessible error amplifier, a pulse
width modulator comparator, three open collector top drive
outputs, and three high current totem pole bottom driver
outputs ideally suited for driving power MOSFETs.
Included in the MC33035 are protective features
consisting of undervoltage lockout, cyclebycycle current
limiting with a selectable time delayed latched shutdown
mode, internal thermal shutdown, and a unique fault output
that can easily be interfaced to a microprocessor controller.
Typical motor control functions include open loop speed
control, forward or reverse rotation, run enable, and
dynamic braking. In addition, the MC33035 has a 60
°
/120
°
select pin which configures the rotor position decoder for
either 60
°
or 120
°
sensor electrical phasing inputs.
FUNCTIONAL DESCRIPTION
A representative internal block diagram is shown in
Figure 19 with various applications shown in Figures 36, 38,
39, 43, 45, and 46. A discussion of the features and function
of each of the internal blocks given below is referenced to
Figures 19 and 36.
Rotor Position Decoder
An internal rotor position decoder monitors the three
sensor inputs (Pins 4, 5, 6) to provide the proper sequencing
of the top and bottom drive outputs. The sensor inputs are
designed to interface directly with open collector type Hall
Effect switches or opto slotted couplers. Internal pullup
resistors are included to minimize the required number of
external components. The inputs are TTL compatible, with
their thresholds typically at 2.2 V. The MC33035 series is
designed to control three phase motors and operate with four
of the most common conventions of sensor phasing. A
60
°
/120
°
Select (Pin 22) is conveniently provided and
affords the MC33035 to configure itself to control motors
having either 60
°
, 120
°
, 240
°
or 300
°
electrical sensor
phasing. With three sensor inputs there are eight possible
input code combinations, six of which are valid rotor
positions. The remaining two codes are invalid and are
usually caused by an open or shorted sensor line. With six
valid input codes, the decoder can resolve the motor rotor
position to within a window of 60 electrical degrees.
The Forward/Reverse input (Pin 3) is used to change the
direction of motor rotation by reversing the voltage across
the stator winding. When the input changes state, from high
to low with a given sensor input code (for example 100), the
enabled top and bottom drive outputs with the same alpha
designation are exchanged (A
T
to A
B
, B
T
to B
B
, C
T
to C
B
).
In effect, the commutation sequence is reversed and the
motor changes directional rotation.
Motor on/off control is accomplished by the Output
Enable (Pin 7). When left disconnected, an internal 25
μ
A
current source enables sequencing of the top and bottom
drive outputs. When grounded, the top drive outputs turn off
and the bottom drives are forced low, causing the motor to
coast and the Fault output to activate.
Dynamic motor braking allows an additional margin of
safety to be designed into the final product. Braking is
accomplished by placing the Brake Input (Pin 23) in a high
state. This causes the top drive outputs to turn off and the
bottom drives to turn on, shorting the motorgenerated back
EMF. The brake input has unconditional priority over all
other inputs. The internal 40 k
pullup resistor simplifies
interfacing with the system safetyswitch by insuring brake
activation if opened or disconnected. The commutation
logic truth table is shown in Figure 20. A four input NOR
gate is used to monitor the brake input and the inputs to the
three top drive output transistors. Its purpose is to disable
braking until the top drive outputs attain a high state. This
helps to prevent simultaneous conduction of the the top and
bottom power switches. In half wave motor drive
applications, the top drive outputs are not required and are
normally left disconnected. Under these conditions braking
will still be accomplished since the NOR gate senses the
base voltage to the top drive output transistors.
Error Amplifier
A high performance, fully compensated error amplifier
with access to both inputs and output (Pins 11, 12, 13) is
provided to facilitate the implementation of closed loop
motor speed control. The amplifier features a typical DC
voltage gain of 80 dB, 0.6 MHz gain bandwidth, and a wide
input common mode voltage range that extends from ground
to V
ref
. In most open loop speed control applications, the
amplifier is configured as a unity gain voltage follower with
the noninverting input connected to the speed set voltage
source. Additional configurations are shown in Figures 31
through 35.
Oscillator
The frequency of the internal ramp oscillator is
programmed by the values selected for timing components
R
T
and C
T
. Capacitor C
T
is charged from the Reference
Output (Pin 8) through resistor R
T
and discharged by an
internal discharge transistor. The ramp peak and valley
voltages are typically 4.1 V and 1.5 V respectively. To
provide a good compromise between audible noise and
output switching efficiency, an oscillator frequency in the
range of 20 to 30 kHz is recommended. Refer to Figure 1 for
component selection.
相關PDF資料 |
PDF描述 |
|---|---|
| NCV33039 | Closed Loop Brushless Motor Adapter(閉環無刷電機適配器) |
| NCV33063A | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| NCV33064DM-5R2 | UNDERVOLTAGE SENSING CIRCUIT |
| NCV33064P-5RA | UNDERVOLTAGE SENSING CIRCUIT |
| NCV33064P-5RP | UNDERVOLTAGE SENSING CIRCUIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV33035DWR2G | 功能描述:馬達/運動/點火控制器和驅動器 DC Brushless Motor Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| NCV33035DWR2G-CUT TAPE | 制造商:ON 功能描述:MC Series 40 V Surface Mount Brushless DC Motor Controller - SOIC-24L |
| NCV33039 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Closed Loop Brushless Motor Adapter |
| NCV33039DR2 | 功能描述:馬達/運動/點火控制器和驅動器 Brushless Closed RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| NCV33039DR2G | 功能描述:馬達/運動/點火控制器和驅動器 Brushless Closed Loop Motor Adaptor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。