- 您現在的位置：買賣IC網 > PDF目錄363233 > NCV33035DWR2 (ON SEMICONDUCTOR) Brushless DC Motor Controller PDF資料下載
參數資料
| 型號： | NCV33035DWR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | Brushless DC Motor Controller |
| 中文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.1 A, PDSO24 |
| 封裝： | PLASTIC, SOP-24 |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 430K |
| 代理商： | NCV33035DWR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MC33035, NCV33035
http://onsemi.com
8
PIN FUNCTION DESCRIPTION
Pin
Symbol
Description
1, 2, 24
B
T
, A
T
, C
T
These three open collector Top Drive outputs are designed to drive the external
upper power switch transistors.
3
Fwd/Rev
S
A
, S
B
, S
C
Output Enable
Reference Output
The Forward/Reverse Input is used to change the direction of motor rotation.
These three Sensor Inputs control the commutation sequence.
A logic high at this input causes the motor to run, while a low causes it to coast.
This output provides charging current for the oscillator timing capacitor C
T
and a
reference for the error amplifier. It may also serve to furnish sensor power.
4, 5, 6
7
8
9
Current Sense Noninverting Input
A 100 mV signal, with respect to Pin 15, at this input terminates output switch
conduction during a given oscillator cycle. This pin normally connects to the top
side of the current sense resistor.
The Oscillator frequency is programmed by the values selected for the timing
components, R
T
and C
T
.
This input is normally connected to the speed set potentiometer.
This input is normally connected to the Error Amp Output in open loop
applications.
10
Oscillator
11
12
Error Amp Noninverting Input
Error Amp Inverting Input
13
14
Error Amp Out/PWM Input
Fault Output
This pin is available for compensation in closed loop applications.
This open collector output is active low during one or more of the following
conditions: Invalid Sensor Input code, Enable Input at logic 0, Current Sense
Input greater than 100 mV (Pin 9 with respect to Pin 15), Undervoltage Lockout
activation, and Thermal Shutdown.
Reference pin for internal 100 mV threshold. This pin is normally connected to
the bottom side of the current sense resistor.
15
Current Sense Inverting Input
16
Gnd
This pin supplies a ground for the control circuit and should be referenced back
to the power source ground.
17
V
CC
This pin is the positive supply of the control IC. The controller is functional over a
minimum V
CC
range of 10 to 30 V.
The high state (V
) of the Bottom Drive Outputs is set by the voltage applied to
this pin. The controller is operational over a minimum V
C
range of 10 to 30 V.
These three totem pole Bottom Drive Outputs are designed for direct drive of the
external bottom power switch transistors.
18
V
C
19, 20, 21
C
B
, B
B
, A
B
22
60
°
/120
°
Select
The electrical state of this pin configures the control circuit operation for either
60
°
(high state) or 120
°
(low state) sensor electrical phasing inputs.
A logic low state at this input allows the motor to run, while a high state does not
allow motor operation and if operating causes rapid deceleration.
23
Brake
相關PDF資料 |
PDF描述 |
|---|---|
| NCV33039 | Closed Loop Brushless Motor Adapter(閉環無刷電機適配器) |
| NCV33063A | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| NCV33064DM-5R2 | UNDERVOLTAGE SENSING CIRCUIT |
| NCV33064P-5RA | UNDERVOLTAGE SENSING CIRCUIT |
| NCV33064P-5RP | UNDERVOLTAGE SENSING CIRCUIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV33035DWR2G | 功能描述:馬達/運動/點火控制器和驅動器 DC Brushless Motor Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| NCV33035DWR2G-CUT TAPE | 制造商:ON 功能描述:MC Series 40 V Surface Mount Brushless DC Motor Controller - SOIC-24L |
| NCV33039 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Closed Loop Brushless Motor Adapter |
| NCV33039DR2 | 功能描述:馬達/運動/點火控制器和驅動器 Brushless Closed RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| NCV33039DR2G | 功能描述:馬達/運動/點火控制器和驅動器 Brushless Closed Loop Motor Adaptor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。