參數資料
型號： NCV33035DWR2
廠商： ON SEMICONDUCTOR
元件分類： 運動控制電子
英文描述： Brushless DC Motor Controller
中文描述： BRUSHLESS DC MOTOR CONTROLLER, 0.1 A, PDSO24
封裝： PLASTIC, SOP-24
文件頁數： 11/28頁
文件大?。?/td> 430K
代理商： NCV33035DWR2
MC33035, NCV33035
http://onsemi.com
11
V
V
V
V
V
V
X
1
0
1
1
1
1
0
0
0
0
(Note 11)
NOTES:
1. V = Any one of six valid sensor or drive combinations X = Don’t care.
2. The digital inputs (Pins 3, 4, 5, 6, 7, 22, 23) are all TTL compatible. The current sense input (Pin 9) has a 100 mV threshold with respect to Pin 15.
A logic 0 for this input is defined as < 85 mV, and a logic 1 is > 115 mV.
3. The fault and top drive outputs are open collector design and active in the low (0) state.
4. With 60
°
/120
°
select (Pin 22) in the high (1) state, configuration is for 60
°
sensor electrical phasing inputs. With Pin 22 in low (0) state, configuration
is for 120
°
sensor electrical phasing inputs.
5. Valid 60
°
or 120
°
sensor combinations for corresponding valid top and bottom drive outputs.
6. Invalid sensor inputs with brake = 0; All top and bottom drives off, Fault low.
7. Invalid sensor inputs with brake = 1; All top drives off, all bottom drives on, Fault low.
8. Valid 60
°
or 120
°
sensor inputs with brake = 1; All top drives off, all bottom drives on, Fault high.
9. Valid sensor inputs with brake = 1 and enable = 0; All top drives off, all bottom drives on, Fault low.
10. Valid sensor inputs with brake = 0 and enable = 0; All top and bottom drives off, Fault low.
11.
All bottom drives off, Fault low.
Figure 20. Three Phase, Six Step Commutation Truth Table (Note 1)
Pulse Width Modulator
The use of pulse width modulation provides an energy
efficient method of controlling the motor speed by varying
the average voltage applied to each stator winding during the
commutation sequence. As C
T
discharges, the oscillator sets
both latches, allowing conduction of the top and bottom
drive outputs. The PWM comparator resets the upper latch,
terminating the bottom drive output conduction when the
positivegoing ramp of C
T
becomes greater than the error
amplifier output. The pulse width modulator timing diagram
is shown in Figure 21. Pulse width modulation for speed
control appears only at the bottom drive outputs.
Current Limit
Continuous operation of a motor that is severely
overloaded results in overheating and eventual failure.
This destructive condition can best be prevented with the use
of cyclebycycle current limiting. That is, each oncycle
is treated as a separate event. Cyclebycycle current
limiting is accomplished by monitoring the stator current
buildup each time an output switch conducts, and upon
sensing an over current condition, immediately turning off
the switch and holding it off for the remaining duration of
oscillator rampup period. The stator current is converted to
a voltage by inserting a groundreferenced sense resistor R
S
(Figure 36) in series with the three bottom switch transistors
(Q
4
, Q
5
, Q
6
). The voltage developed across the sense
resistor is monitored by the Current Sense Input (Pins 9 and
15), and compared to the internal 100 mV reference. The
current sense comparator inputs have an input common
mode range of approximately 3.0 V. If the 100 mV current
sense threshold is exceeded, the comparator resets the lower
sense latch and terminates output switch conduction. The
value for the current sense resistor is:
RS
0.1
Istator(max)
The Fault output activates during an over current condition.
The duallatch PWM configuration ensures that only one
single output conduction pulse occurs during any given
oscillator cycle, whether terminated by the output of the
error amp or the current limit comparator.
相關PDF資料
PDF描述
NCV33039 Closed Loop Brushless Motor Adapter(閉環無刷電機適配器)
NCV33063A 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C
NCV33064DM-5R2 UNDERVOLTAGE SENSING CIRCUIT
NCV33064P-5RA UNDERVOLTAGE SENSING CIRCUIT
NCV33064P-5RP UNDERVOLTAGE SENSING CIRCUIT
相關代理商/技術參數
參數描述
NCV33035DWR2G 功能描述:馬達/運動/點火控制器和驅動器 DC Brushless Motor Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
NCV33035DWR2G-CUT TAPE 制造商:ON 功能描述:MC Series 40 V Surface Mount Brushless DC Motor Controller - SOIC-24L
NCV33039 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Closed Loop Brushless Motor Adapter
NCV33039DR2 功能描述:馬達/運動/點火控制器和驅動器 Brushless Closed RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
NCV33039DR2G 功能描述:馬達/運動/點火控制器和驅動器 Brushless Closed Loop Motor Adaptor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*