- 您現在的位置：買賣IC網 > PDF目錄361102 > NCP5214AMNR2G (ON SEMICONDUCTOR) 2−in−1 Notebook DDR Power Controller PDF資料下載
參數資料
| 型號： | NCP5214AMNR2G |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | 2−in−1 Notebook DDR Power Controller |
| 中文描述： | 3 A SWITCHING CONTROLLER, 460 kHz SWITCHING FREQ-MAX, DSO22 |
| 封裝： | LEAD FREE, DFN-22 |
| 文件頁數： | 25/31頁 |
| 文件大小： | 376K |
| 代理商： | NCP5214AMNR2G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁
NCP5214A
http://onsemi.com
25
Thus, inductor with 1.8 H inductance, 14 A maximum
rated DC current and 3.5 m DCR is chosen.
c. Calculate ESR and capacitance of output filter
capacitor:
First, the ESR required to achieve the desired output
ripple voltage is considered. Suppose the output ripple
voltage is 2% of the nominal output voltage.
(0.02
1.8 V)
1.8 H
(20 V1.8 V)
15.8 m
ESR
400 kHz
1.8 V
20 V
(eq. 48)
Second, the ESR required to meet the transient load
undershoot requirement is considered, such that:
100 mV
7 A
Therefore, the suitable ESR is 12 m or smaller, and the
value of 7.5 m is selected for more design margin and
better performance. Then, two same SPCaps or POSCAPs
each with 15 m ESR in parallel having a resultant ESR
of 7.5 m should be good enough to meet the
requirements.
Then, check that whether the previously supposed
capacitance meets the undershoot and overshoot
requirements.
ESR
14.3 m
(eq. 49)
To ensure that undershoot requirement of less than 100 mV is achieved, the capacitance must be:
COUT
7 A
100 mV7 A
7.5 m
1
1.8 V36 mV
20 V
400 kHz
335.9 F
(eq. 50)
To make sure that overshoot requirement of less than 100 mV is fulfilled, capacitance must be:
COUT
1.8 H
7 A
(20 V1.836 V)
2
1.8 H
1.836 V)2 (1.836 V)2
1.836 V
400 kHz
20 V
2
(100 mV
317.6 F
(eq. 51)
Therefore, output capacitor with capacitance of 440 F
should meet both undershoot and overshoot requirements.
Sometimes, it may take several times of iterations between
the process of selecting inductance of the inductor and ESR
and capacitance of the output capacitor.
Then, the voltage rating of the output capacitor is
estimated by:
Vrated
1.25
Thus, output capacitor with 2.5 V or larger rated voltage
is used.
Finally, the rated rms ripple current of the output
capacitor is considered:
(20 V1.836 V)
1.8 H
1.836 V
2.3 V
(eq. 52)
ICOUT(rms)
1.836 V
20 V
400 kHz
2.3 A
(eq. 53)
Thus, capacitor with rated rms ripple current of 3.0 A or
larger should be selected. Two capacitors each with 1.5 A
rated ripple current can be connected in parallel to provide
a total of 3.0 A rated rms ripple current.
Therefore, two same capacitors in parallel each with
capacitance of 220 F, ESR of 15 m , rated voltage of
2.5 V, and rated rms ripple current of 1.5 A are used.
d.Calculate the resistance value of OCP current limit
setting resistor:
First, the OCP current limit is estimated at maximum
load condition, such that:
(20 V1.836 V)
2
11.16 A
ILIMIT
8 A
2 A
1.836 V
1.8 H
400 kHz
20 V
(eq. 54)
Thus, I
LIMIT
is set to 11.5 A. Suppose from the highside
MOSFET data sheet, the maximum R
DS(on)
is 10 m .
Then, the value of RL1 is calculated by:
11.5 A
26 A
Therefore, the resistor with standard value of 4.7 k is
selected for RL1.
e. Calculate the RC values of the compensation network:
First, 4.3 k is chosen as the value of R
1
which is in the
range between 2.0 k and 5.0 k
Since the worst case of stability is at the maximum V
IN
,
the close loop compensation should be considered at
maximum V
IN
. Then the ramp amplitude can be calculated
as below:
VRAMP
1.25 V
0.045
RL1
10 m
4.4 k
(eq. 55)
(20 V5 V)
1.925 V
(eq. 56)
Since the L = 1.8 H, C
OUT
= 440 F, and the target close loop bandwidth is 100 kHz, the value of R
3
can be
calculated as:
2
100 kHz
1.925 V
4.3 k
20 V
R3
1.8 H
440 F
7.3 k
(eq. 57)
相關PDF資料 |
PDF描述 |
|---|---|
| NCP5214 | 2-in-1 Notebook DDR Power Controller |
| NCP5214MNR2 | 2-in-1 Notebook DDR Power Controller |
| NCP5218 | 2−in−1 Notebook DDR Power Controller |
| NCP5218MNR2G | 2−in−1 Notebook DDR Power Controller |
| NCP5220 | 3−in−1 PWM Dual Buck and Linear Power Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP5214EVB | 功能描述:電源管理IC開發工具 ANA NCP5214 EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP5214MNR2 | 功能描述:DC/DC 開關控制器 2-IN-1 NOTBOOK DDR CNTLR RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| NCP5214MNR2G | 功能描述:DC/DC 開關控制器 2-IN-1 NOTBOOK DDR CNTLR RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| NCP5215 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual Synchronous Buck Controller for Notebook Power System |
| NCP5215MNR2G | 功能描述:直流/直流開關轉換器 BUCK CONTROLLER RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。