- 您現在的位置：買賣IC網 > PDF目錄361100 > NCP4326DR2 (ON SEMICONDUCTOR) Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies PDF資料下載
參數資料
| 型號： | NCP4326DR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 28/30頁 |
| 文件大?。?/td> | 432K |
| 代理商： | NCP4326DR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁
NCP4326
http://onsemi.com
28
The operational amplifier is an open collector type that it
allows to sink the current from the optocoupler from any
voltage source level.
Figure 53 illustrates an example of a close loop feedback
connection from the secondary and the primary side.
1V25
FBm
CPm
8
GND
9
Rup
Rdown
GND
U5
Opto
R33
1k
CFB_comp
RFB_comp
D1
C1
GND
L1
C2
Prim FB
NCP4326
VOut
Q1
Primary
Controller
Figure 53. Primary Feedback Connection
+
+
+
V
DD1
V
CC
Components Determination
RC Network on Flux Pin
The flux image can be obtained with a negative output or
with a forward configuration. The winding voltage
integration yields the flux image inside the transformer. This
integration will be done with a basic integrator.
The time constant of this integrator should be significantly
large compare to the maximum primary switching period.
For example the time constant can be 510 times larger.
Thus the resistor acts like a constant current source during
the period, so that the voltage across the capacitor rises and
falls linearly.
The internal flux signal (Int_Flux, see Figure 46) is
clamped to 4.5 volts in order to ensure a proper disable
softstart function when the enable pin voltage is at its
maximum value (5.0 V).
For achieving a proper softstart without any action from
the 4.5 V internal clamp, the maximum input voltage on flux
pin must be lower or equal to:
Vclamp
Voffset
OpAmp_gain
that yields
4.5
0.5
10
0.4 V.
So Vflux_pin should be lower or equal to 400 mV when
the power supply is in full load condition and at low line
input voltage.
Practically in case of universal input voltage range and
with a maximum output power to 16 W, a 10 nF capacitor is
selected and the resistor is adjusted to guaranteed a
maximum voltage on the flux to 400 mV at low line input
voltage. This gives a 22 k resistor.
Ct Capacitor
This capacitor is used to create the saw tooth for achieving
the pulse width modulation (PWM) for the both secondary
outputs regulated by the NCP4326.
The capacitor value can be determined with the following
equation:
V
t
(V
CT_max1
V
CT_min
),
Δ
t = primary off time (time during the
capacitor is charged).
The capacitor value is calculated in the worst condition:
I = I
Ctmax
= 700 A
Δ
V = (V
CT_max1
V
CT_min
) = 4.0 1.6 = 2.4 V
Δ
t = maximum primary off time in worst case condition
(Full load and low line input).
I
C
C
I
t
V
, where I = I
Ct
,
Δ
V =
相關PDF資料 |
PDF描述 |
|---|---|
| NCP4326DR2G | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
| NCP4330DR2G | Post Regulation Driver |
| NCP4330 | 300 W 80 PLUS ATX Reference Design |
| NCP4331DR2G | Synchronous Buck Controller for High Efficiency Post Regulation |
| NCP4331 | Synchronous Buck Controller for High Efficiency Post Regulation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP4326DR2G | 功能描述:初級與次級側 PWM 控制器 Quasi Resonant Secondary Side RoHS:否 制造商:ON Semiconductor 輸出端數量:1 開關頻率:250 KHz 工作電源電壓:- 0.3 V to + 28 V 最大工作溫度:+ 85 C 最小工作溫度:- 5 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Reel |
| NCP4328 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Secondary Side CV/CC Controller |
| NCP4328BSNT1G | 制造商:ON Semiconductor 功能描述:REEL / SECONDARY SIDE CONSTANT V |
| NCP432B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Programmable Precision References |
| NCP432BCSNT1G | 制造商:ON Semiconductor 功能描述:PROGRAMMABLE PRECISION RE - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / PROGRAMMABLE PRECISION RE |
發布緊急采購，3分鐘左右您將得到回復。