- 您現在的位置：買賣IC網 > PDF目錄361100 > NCP4326DR2 (ON SEMICONDUCTOR) Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies PDF資料下載
參數資料
| 型號： | NCP4326DR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 18/30頁 |
| 文件大?。?/td> | 432K |
| 代理商： | NCP4326DR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
NCP4326
http://onsemi.com
18
Detailed Regulation Principle
At the beginning of the Ton period the capacitor
connected on Ct pin is discharged and the internal current
source is shunted to V
CT_min
(1.6 V) via the bipolar
transistor until the end of the Ton period.
The internal current source starts to charge the capacitor
connected on Ct pin at the beginning of the Toff period. As
long as the voltage on the Ct pin is below the CPX pin, the
secondary switch is kept ON (i.e.: The secondary switch is
turned ON at the beginning of the primary ontime). By this
method the secondary power MOSFET can only be
switched ON one time per Toff period and prevents from any
hysteretic switching to the secondary side. The secondary
switch is synchronized with the primary switching
frequency, the secondary controller sets only the duty cycle.
The Ct capacitor value determines only the voltage swing
present at the Ct pin, which it used to generate the secondary
duty cycle.
The secondary regulation is working in trailing edge mode
control. The trailing edge mode control has been preferred
for its superior cross load performance.
The following picture (Figure 40) shows only one output
regulation, but the second output regulation works similarly
and independently from the other one. Nevertheless, both
regulations use the same synchronization signal:
Beginning of ON time period (switch ON of the
secondary mosfet)
The same ramp on Ct pin for adjusting in respect to the
error amplifier level the secondary dutycycle to the
both outputs drives.
Figure 40. Detailed Principle Regulation
Toff
Ton
Switch
ON
Switch
OFF
Primary Drain
Voltage (200 V/div)
DRV1 pin signal
(10 V/div)
Ct ramp (2 V/div)
Error amplifier
output voltage (CP1
pin) (2 V/div)
相關PDF資料 |
PDF描述 |
|---|---|
| NCP4326DR2G | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
| NCP4330DR2G | Post Regulation Driver |
| NCP4330 | 300 W 80 PLUS ATX Reference Design |
| NCP4331DR2G | Synchronous Buck Controller for High Efficiency Post Regulation |
| NCP4331 | Synchronous Buck Controller for High Efficiency Post Regulation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP4326DR2G | 功能描述:初級與次級側 PWM 控制器 Quasi Resonant Secondary Side RoHS:否 制造商:ON Semiconductor 輸出端數量:1 開關頻率:250 KHz 工作電源電壓:- 0.3 V to + 28 V 最大工作溫度:+ 85 C 最小工作溫度:- 5 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Reel |
| NCP4328 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Secondary Side CV/CC Controller |
| NCP4328BSNT1G | 制造商:ON Semiconductor 功能描述:REEL / SECONDARY SIDE CONSTANT V |
| NCP432B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Programmable Precision References |
| NCP432BCSNT1G | 制造商:ON Semiconductor 功能描述:PROGRAMMABLE PRECISION RE - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / PROGRAMMABLE PRECISION RE |
發布緊急采購，3分鐘左右您將得到回復。