- 您現在的位置：買賣IC網 > PDF目錄361100 > NCP4326DR2 (ON SEMICONDUCTOR) Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies PDF資料下載
參數資料
| 型號： | NCP4326DR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 21/30頁 |
| 文件大小： | 432K |
| 代理商： | NCP4326DR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
NCP4326
http://onsemi.com
21
The new patented softstart is based on the flux
transformer reconstruction concept with leading edge mode
control during a startup sequence only.
A startup sequence can be arisen with the 3 following
cases:
1. The power supply unit is just plug on the main
supply, in this case there is a general startup.
2. The power supply unit is running but one or the
both outputs are disabled, thus by enabling the
output a new startup happened.
3. The power supply unit is running but the
secondary controller is in standby mode (STBY
pin grounded), when the standby mode is left, a
startup sequence happen if at least one of the
outputs is enable.
The idea of this softstart is to reconstruct the flux image
inside the flyback transformer, and to compare this image
with a slow ramp up voltage on enable pin, to generate a
smooth increasing duty cycle in leading edge mode. The
leading edge mode control guarantees that the peak current
ramps up smoothly. Because the secondary duty cycle
finishes at the OFFtime end and starts just before.
At the end of the off time period and due to the primary
controller running in critical conduction mode; the flux in
the transformer is null, so the peak will start from zero to
reach the nominal value.
Figure 44 illustrates the driver synchronization in
softstart sequence.
0
t
0
t
0
t
Verror
VCt
DRV
0
t
0
t
ID2
Transfo Flux
Vsync
OFF Time
ON Time
EN voltage
Figure 44. Startup Sequence Illustrating the Leading Edge Mode Control
Due to the internal current source and the external
capacitor connected on enable pin (EN1 and EN2 pin); a
voltage ramp is generated that it fixes the softstart time; by
playing with the capacitor value the softstart time can be
adjusted to fit the application startup time.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP4326DR2G | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
| NCP4330DR2G | Post Regulation Driver |
| NCP4330 | 300 W 80 PLUS ATX Reference Design |
| NCP4331DR2G | Synchronous Buck Controller for High Efficiency Post Regulation |
| NCP4331 | Synchronous Buck Controller for High Efficiency Post Regulation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP4326DR2G | 功能描述:初級與次級側 PWM 控制器 Quasi Resonant Secondary Side RoHS:否 制造商:ON Semiconductor 輸出端數量:1 開關頻率:250 KHz 工作電源電壓:- 0.3 V to + 28 V 最大工作溫度:+ 85 C 最小工作溫度:- 5 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Reel |
| NCP4328 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Secondary Side CV/CC Controller |
| NCP4328BSNT1G | 制造商:ON Semiconductor 功能描述:REEL / SECONDARY SIDE CONSTANT V |
| NCP432B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Programmable Precision References |
| NCP432BCSNT1G | 制造商:ON Semiconductor 功能描述:PROGRAMMABLE PRECISION RE - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / PROGRAMMABLE PRECISION RE |
發布緊急采購，3分鐘左右您將得到回復。