- 您現在的位置：買賣IC網 > PDF目錄361091 > NCP1381 (ON SEMICONDUCTOR) Low−Standby High Performance PWM Controller PDF資料下載
參數資料
| 型號： | NCP1381 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Low−Standby High Performance PWM Controller |
| 文件頁數： | 24/26頁 |
| 文件大小： | 559K |
| 代理商： | NCP1381 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁
NCP1381
http://onsemi.com
24
A mix of conditions, BO, shortcircuit and UVLO fault are represented on this diagram. In BO, the pulses (pulse ok signal) are started at
V
CC
= 15 V and there is no latchoff phase. In shortcircuit, pulses are stopped by the timer and finally, in a UVLO conditions (not a
shortcircuit), there is a latchoff phase but the timer is flat since there is no shortcircuit.
Figure 37.
50.0m
150m
250m
350m
450m
V
CC
VCC
ON
VCC
OFF
VCC
latch
Timer
V
in
UVLO Interruption
ShortCircuit
Interruption
BO Interruption
B
OK
Comp.
Pulse
OK
PFC Behavior During BO Conditions
During brownout, the PFC is disabled; otherwise the
PFC controller consumption would prevent the charging of
the V
CC
capacitor. The PFC will be shutdown until BO
comes back and a clean startup sequence has properly ended.
Softstart
The NCP1381 features a softstart activated during the
power on sequence (P
ON
) and in shortcircuit conditions to
lower the acoustical noise in the transformer. As soon as
V
CC
reaches 15 V, the peak current is gradually increased
from nearly zero up to the maximum clamping level (e.g.
0.8 V / R
sense
). Every restart attempt is followed by a
softstart activation.
A shorter softstart is also activated during the skip cycle
condition to implement our softburst. This SoftSkip is
cancelled whenever a fault condition appears, in order not to
degrade the transient behavior in case of load transients
when the controller is initially in skip mode.
Figure 38. SoftStart is Activated During a Startup
Sequence or an OCP Condition
15 V
V
CC
Current
Sense
0 V (Fresh P
ON
)
or V
CClatch
5 ms
Max I
P
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1381DR2G | Low−Standby High Performance PWM Controller |
| NCP1395APG | High Performance Resonant Mode Controller |
| NCP1395ADR2G | High Performance Resonant Mode Controller |
| NCP1395BDR2G | High Performance Resonant Mode Controller |
| NCP1395BPG | High Performance Resonant Mode Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1381 AM90 WAF | 制造商:ON Semiconductor 功能描述: |
| NCP1381ADAPEVB | 功能描述:BOARD EVAL NCP1381 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| NCP1381DR2G | 功能描述:電流型 PWM 控制器 ANA PWM CONTROLLER RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1382DR2G | 功能描述:電流型 PWM 控制器 L-STNDBY PWM CNTRLR RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1392B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High-Voltage Half-Bridge Driver with Inbuilt Oscillator |
發布緊急采購，3分鐘左右您將得到回復。