參數資料
型號： NCN6001
廠商： ON SEMICONDUCTOR
英文描述： Compact Smart Card Interface IC
中文描述： 緊湊型智能卡接口IC
文件頁數： 14/36頁
文件大?。?/td> 332K
代理商： NCN6001
NCN6001
http://onsemi.com
14
START UP DEFAULT CONDITIONS
At start up, when the V
CC
power supply is turned on, the
internal POR circuit sets the chip in the default conditions as
defined in Table 4.
Table 4. Start Up Default Conditions
CRD_DET
Normally Open
CRD_VCC
Off
CRD_CLK
t
r
and t
f
= SLOW
CRD_CLK
Low
Protocol
Special Mode
CARD DETECTION
The card is detected by the external switch connected pin
18. The internal circuit provides a positive bias of this pin
and the polarity of the insertion/extraction is programmable
by the MOSI protocol as depicted in Table 2.
The bias current is 1.0 A typical and care must be
observed to avoid leakage to ground from this pin to
maintain the logic function. In particular, using a low
impedance probe (< 1.0 M ) may lead to uncontrolled
operation during the debug.
Depending upon the programmed condition, the card can
be detected either by a Normally Open (default condition) or
a Normally Close switch (Table 2). On the other hand, the
meaning of the feedback message contained in the MISO
register bit b4, depends upon the SPI mode of operation as
defined here below:
SPI Normal Mode:
the MISO bit b4 is High when a card is
inserted, whatever be the polarity of the card detect switch.
SPI Special Mode:
the MISO bit b4 copies the logic state of
the Card detect switch as depicted here below, whatever be
the polarity of the switch used to handle the detection:
CRD_DET = Low
→
MISO/b4 = Low
CRD_DET = High
→
MISO/b4 = High
CRD_VCC OPERATION
The built-in DC/DC converter provides the CRD_VCC
voltage and can be programmed to run one of the three
possible values, 1.8 V, 3.0 V or 5.0 V, assuming the input
voltage V
CC
is within the 2.7 V to 5.5 V range. In any case,
CRD_VCC is voltage regulated, together with a current
overload detection. On the other hand, the power conversion
is automatically switched to handle either a boost or a buck
mode of operation, depending upon the difference between
the input voltage V
CC
and the output supply CRD_VCC.
The CRD_VCC output current is a function of the V
CC
input value as depicted in Table 5.
Table 5. CRD_VCC Output Voltage Range
CRD_VCC
Comments
1.80 V
Maximum Output DC Current = 35 mA
3.0 V
Maximum Output DC Current = 60 mA
5.0 V
Maximum Output DC Current = 65 mA
Whatever the CRD_VCC output voltage may be, a
built-in comparator makes sure the voltage is within the
ISO7816-3/ EMV specifications. If the voltage is no longer
within the minimum/maximum values, the DC/DC is
switched Off, the Power Down sequence takes place and an
interrupt is presented at the INT pin 2.
POWER UP SEQUENCE
The Power Up Sequence makes sure all the card related
signals are Low during the CRD_VCC positive going slope.
These lines are validated when CRD_VCC is above the
minimum specified voltage (depending upon the
programmed CRD_VCC value).
Figure 3. Typical Start Up CRD_VCC Sequence
相關PDF資料
PDF描述
NCN6004AFTBR2 Dual SAM/SIM Interface Integrated Circuit
NCN6004A Dual SAM/SIM Interface Integrated Circuit
NCN6010DTBR2 SIM Card Supply and Level Shifter
NCN6010 SIM Card Supply and Level Shifter
NCN6010D SIM Card Supply and Level Shifter
相關代理商/技術參數
參數描述
NCN6001/D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC
NCN6001_06 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Smart Card Interface IC
NCN6001_0610 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smartcard Interface ICs
NCN6001DTBEVB 功能描述:界面開發工具 NCN6001 TSSOP EVAL BOARD RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
NCN6001DTBR2 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*