- 您現在的位置：買賣IC網 > PDF目錄380571 > MX29LV320MTMI-70R (Macronix International Co., Ltd.) 64M-BIT SINGLE VOLTAGE 3V ONLY UNIFORM SECTOR FLASH MEMORY PDF資料下載
參數資料
| 型號： | MX29LV320MTMI-70R |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 64M-BIT SINGLE VOLTAGE 3V ONLY UNIFORM SECTOR FLASH MEMORY |
| 中文描述： | 6400位單電壓3V時僅均勻部門閃存 |
| 文件頁數： | 15/70頁 |
| 文件大小： | 555K |
| 代理商： | MX29LV320MTMI-70R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
15
P/N:PM1093
REV. 1.1, AUG. 11, 2005
MX29LV64xM H/L
It is also possible to determine if the group is protected
in the system by writing a Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
a logical "1" at Q0 for the protected sector.
CHIP UNPROTECT OPERATION
The MX29LV64xM H/L also features the chip unprotect
mode, so that all sectors are unprotected after chip
unprotect is completed to incorporate any changes in
the code. It is recommended to protect all sectors before
activating chip unprotect mode.
To activate this mode, the programming equipment must
force VID on control pin OE# and address pin A9. The
CE# pins must be set at VIL. Pins A6 must be set to
VIH. (see Table 2) Refer to chip unprotect algorithm and
waveform for the chip unprotect algorithm. The unprotect
mechanism begins on the falling edge of the WE# pulse
and is terminated on the rising edge.
MX29LV64xM H/L also provides another method. Which
requires VID on the RESET# only. This method can be
implemented either in-system or via programming equip-
ment. This method uses standard microprocessor bus
cycle timing.
It is also possible to determine if the chip is unprotect in
the system by writing the Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
00H at data outputs (Q0-Q7) for an unprotect sector. It is
noted that all sectors are unprotected after the chip
unprotect algorithm is completed.
WRITE PROTECT (WP#)
The write protect function provides a hardware method
to protect sector without using V
ID
.
If the system asserts VIL on the WP# pin, the device
disables program and erase functions in the first
(MX29LV64xMH) or last (MX29LV64xML) sector inde-
pendently of whether those sectors were protected or
unprotect using the method described in Sector/Sector
Group Protection and Chip Unprotect".
If the system asserts VIH on the WP# pin, the device
reverts to whether the first (MX29LV64xMH) or last
(MX29LV64xML) sector were last set to be protected or
unprotect. That is, sector protection or unprotection for
these two sectors depends on whether they were last
protected or unprotect using the method described in
"Sector/Sector Group Protection and Chip Unprotect".
Note that the WP# pin must not be left floating or uncon-
nected; inconsistent behavior of the device may result.
TEMPORARY SECTOR GROUP UNPROTECT
OPERATION
This feature allows temporary unprotect of previously
protected sector to change data in-system. The Tempo-
rary Sector Unprotect mode is activated by setting the
RESET# pin to VID(11.5V-12.5V). During this mode, for-
merly protected sectors can be programmed or erased
as unprotect sector. Once VID is remove from the RE-
SET# pin, all the previously protected sectors are pro-
tected again.
SILICON ID READ OPERATION
Flash memories are intended for use in applications where
the local CPU alters memory contents. As such, manu-
facturer and device codes must be accessible while the
device resides in the target system. PROM program-
mers typically access signature codes by raising A9 to
a high voltage. However, multiplexing high voltage onto
address lines is not generally desired system design prac-
tice.
MX29LV64xM H/L provides hardware method to access
the silicon ID read operation. Which method requires VID
on A9 pin, VIL on CE#, OE#, A6, and A1 pins. Which
apply VIL on A0 pin, the device will output MXIC's manu-
facture code of which apply VIH on A0 pin, the device will
output MX29LV64xM H/L device code.
VERIFY SECTOR GROUP PROTECT STATUS
OPERATION
MX29LV64xM H/L provides hardware method for sector
group protect status verify. Which method requires VID
on A9 pin, VIH on WE# and A1 pins, VIL on CE#, OE#,
A6, and A0 pins, and sector address on A16 to A21 pins.
Which the identified sector is protected, the device will
output 01H. Which the identified sector is not protect, the
device will output 00H.
相關PDF資料 |
PDF描述 |
|---|---|
| MX29LV320MTMI-90G | 64M-BIT SINGLE VOLTAGE 3V ONLY UNIFORM SECTOR FLASH MEMORY |
| MX29LV320MTMI-90R | 64M-BIT SINGLE VOLTAGE 3V ONLY UNIFORM SECTOR FLASH MEMORY |
| MX29LV320MTXC-70G | 64M-BIT SINGLE VOLTAGE 3V ONLY UNIFORM SECTOR FLASH MEMORY |
| MX29LV320MTXC-70R | 64M-BIT SINGLE VOLTAGE 3V ONLY UNIFORM SECTOR FLASH MEMORY |
| MX29LV320MTXC-90G | 64M-BIT SINGLE VOLTAGE 3V ONLY UNIFORM SECTOR FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MX29LV400BTC70 | 制造商:MX 功能描述:New |
| MX29LV400CBMC-55Q | 制造商:Macronix International Co Ltd 功能描述:IC FLASH 4MBIT 55NS 44SOP |
| MX29LV400CBMC-70G | 制造商:Macronix International Co Ltd 功能描述:IC FLASH 4MBIT 70NS 44SOP |
| MX29LV400CBMC-90G | 制造商:Macronix International Co Ltd 功能描述:IC FLASH 4MBIT 90NS 44SOP |
| MX29LV400CBMI-70G | 功能描述:IC FLASH PAR 3V 4MB 70NS 44SOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:MX29LV 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。