- 您現在的位置：買賣IC網 > PDF目錄98046 > MTD2955ET4 (ON SEMICONDUCTOR) 12 A, 60 V, 0.3 ohm, P-CHANNEL, Si, POWER, MOSFET PDF資料下載
參數資料
| 型號： | MTD2955ET4 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | JFETs |
| 英文描述： | 12 A, 60 V, 0.3 ohm, P-CHANNEL, Si, POWER, MOSFET |
| 封裝： | CASE 369A-13, DPAK-3 |
| 文件頁數： | 2/11頁 |
| 文件大?。?/td> | 278K |
| 代理商： | MTD2955ET4 |
MTD2955E
http://onsemi.com
10
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of
control settings that will give the desired heat pattern. The
operator must set temperatures for several heating zones,
and a figure for belt speed. Taken together, these control
settings make up a heating “profile” for that particular
circuit board. On machines controlled by a computer, the
computer remembers these profiles from one operating
session to the next. Figure 17 shows a typical heating profile
for use when soldering a surface mount device to a printed
circuit board. This profile will vary among soldering
systems but it is a good starting point. Factors that can affect
the profile include the type of soldering system in use,
density and types of components on the board, type of solder
used, and the type of board or substrate material being used.
This profile shows temperature versus time. The line on the
graph shows the actual temperature that might be
experienced on the surface of a test board at or near a central
solder joint. The two profiles are based on a high density and
a
low
density
board.
The
Vitronics
SMD310
convection/infrared reflow soldering system was used to
generate this profile. The type of solder used was 62/36/2
Tin Lead Silver with a melting point between 177189°C.
When this type of furnace is used for solder reflow work, the
circuit boards and solder joints tend to heat first. The
components on the board are then heated by conduction. The
circuit board, because it has a large surface area, absorbs the
thermal energy more efficiently, then distributes this energy
to the components. Because of this effect, the main body of
a component may be up to 30 degrees cooler than the
adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
RAMP"
STEP 2
VENT
SOAK"
STEP 3
HEATING
ZONES 2 & 5
RAMP"
STEP 4
HEATING
ZONES 3 & 6
SOAK"
STEP 5
HEATING
ZONES 4 & 7
SPIKE"
STEP 6
VENT
STEP 7
COOLING
200°C
150°C
100°C
50°C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205° TO 219°C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100°C
150°C
160°C
170°C
140°C
Figure 17. Typical Solder Heating Profile
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
相關PDF資料 |
PDF描述 |
|---|---|
| MTD2955VT4 | 12 A, 60 V, 0.23 ohm, P-CHANNEL, Si, POWER, MOSFET |
| MTD2N40E | 2 A, 400 V, 3.5 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTD2N50E1 | 2 A, 500 V, 3.6 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTD2N50E | 2 A, 500 V, 3.6 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MTD3302 | 8300 mA, 30 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MTD2955V | 功能描述:MOSFET DISC BY MFG 2/02 RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| MTD2955V1 | 制造商:ON Semiconductor 功能描述:Trans MOSFET P-CH 60V 12A 3-Pin(3+Tab) IPAK Rail |
| MTD2955V-1 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power MOSFET 12A, 60V P-Channel DPAK |
| MTD2955V-1G | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power MOSFET 12A, 60V P-Channel DPAK |
| MTD2955VG | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power MOSFET 12A, 60V P-Channel DPAK |
發布緊急采購，3分鐘左右您將得到回復。