- 您現在的位置：買賣IC網 > PDF目錄45388 > MSC1211Y2PAGTG4 (TEXAS INSTRUMENTS INC) 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MSC1211Y2PAGTG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | GREEN, PLASTIC, TQFP-64 |
| 文件頁數： | 43/111頁 |
| 文件大?。?/td> | 1102K |
| 代理商： | MSC1211Y2PAGTG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁
MSC1211, MSC1212
MSC1213,MSC1214
SBAS323G JUNE 2004 REVISED OCTOBER 2007
www.ti.com
37
ACCESSING EXTERNAL MEMORY
If external memory is used, P0 and P2 must be configured
as address and data lines. If external memory is not used, P0
and P2 can be configured as general-purpose I/O lines
through the hardware configuration register (HCR0, HCR1).
To enable access to external memory, bits 0 and 1 of the
HCR1 register must be set to ‘0’. When these bits are
enabled all memory accesses for both internal and
external memory will appear on Ports 0 and 2. During the
data portion of the cycle for internal memory, Port 0 will be
zero for security purposes.
Accesses to external memory are of two types: to external
Program Memory and to external Data Memory. Accesses
to external Program Memory use signal PSEN (program
store enable) as the read strobe. Accesses to external
Data Memory use RD or WR (alternate functions of P3.7
and P3.6) to strobe the memory.
If desired, External Program Memory and external Data
Memory may be combined by applying the RD and PSEN
signals to the inputs of an AND gate and using the output
of the gate as the read strobe to the external Program/Data
Memory.
A program fetch from external Program Memory uses a
16-bit address. Accesses to external Data Memory can
use either a 16-bit address (MOVX @DPTR) or an 8-bit
address (MOVX @RI).
If Port 2 is selected for external memory use (HCR1, bit 0),
it cannot be used as general-purpose I/O. This bit (or Bit
1 of HCR1) also forces bits P3.6 and P3.7 to be used for
WR and RD instead of I/O. Port 2, P3.6, and P3.7 should
all be written to ‘1.’
If an 8-bit address is being used (MOVX @RI), the contents
of the MPAGE (92h) SFR remain at the Port 2 pins
throughout the external memory cycle, which facilitates
paging.
In any case, the low byte of the address is time-multiplexed
with the data byte on Port 0. The ADDR/DATA signals use
CMOS drivers in the Port 0, Port 2, WR, and RD output
buffers. Thus, in this application, the Port 0 pins are not
open-drain outputs, and do not require external pull-ups for
high-speed access. Signal ALE (Address Latch Enable)
should be used to capture the address byte into an external
latch. The address byte is valid at the negative transition
of ALE. Then, in a write cycle, the data byte to be written
appears on Port 0 just before WR is activated, and remains
there until after WR is deactivated. In a read cycle, the
incoming byte is accepted at Port 0 just before the read
strobe is deactivated.
The functions of Port 0 and Port 2 are selected in HCR1.
(Hardware configuration registers can only be changed
during Flash Programming mode.) The default state is for
Port 0 and Port 2 to be used as general-purpose I/O. If an
external memory access is attempted when they are
configured as general-purpose I/O, the values of Port 0
and Port 2 will not be affected.
External Program Memory is accessed under two conditions:
1.
Whenever signal EA is low during reset, then all future
code and data accesses are external; or
2.
Whenever the Program Counter (PC) contains a
number that is outside of the internal Program Memory
address range, if the ports are enabled.
If Port 0 and Port 2 are selected for external memory, all 8
bits of Port 0 and Port 2, as well as P3.6 and P3.7, are
dedicated to an output function and may not be used for
general-purpose I/O. During external program fetches,
Port 2 outputs the high byte of the PC.
Programming Flash Memory
There are four sections of Flash Memory for programming:
1.
128 configuration bytes.
2.
Reset sector (4kB) (not to be confused with the 2kB
Boot ROM).
3.
Program Memory.
4.
Data Memory.
Boot ROM
There is a 2kB Boot ROM that controls operation during
serial or parallel programming. Additionally, the Boot ROM
routines can be accessed during the user mode if it is
enabled. When enabled, the Boot ROM routines will be
located at memory addresses F800hFFFFh during user
mode. In program mode the Boot ROM is located in the first
2kB of Program Memory. For additional information, refer
to Application Note SBAA085, available for download from
the TI web site (www.ti.com).
The MSC1211/12/13/14 are shipped with Flash Memory
erased (all 1s). Parallel programming methods typically
involve a third-party programmer. Serial programming
methods typically involve in-system programming. UAM
allows Code Program and Data Memory programming.
The actual code for Flash programming cannot execute
from Flash. That code must execute from the Boot ROM
or internal (von Neumann) RAM.
相關PDF資料 |
PDF描述 |
|---|---|
| MSC1211Y4PAGTG4 | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| MSC1212Y3PAGTG4 | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| MSC1213Y3PAGTG4 | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| MSC1214Y4PAGR | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
| MSC1213Y4PAGRG4 | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSC1211Y3 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision Analog-to-Digital Converter (ADC) and Digital-to-Analog Converters (DACs) with 8051 Microcontroller and Flash Memory |
| MSC1211Y3PAGR | 功能描述:數據轉換系統 Precision ADC & DACs w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MSC1211Y3PAGRG4 | 功能描述:數據轉換系統 8051 CPU w/ 8kB Mem 24B ADC & Quad 16B RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MSC1211Y3PAGT | 功能描述:數據轉換系統 Precision ADC & DACs w/8051 CPU & Flash RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MSC1211Y3PAGTG4 | 功能描述:數據轉換系統 8051 CPU w/ 8kB Mem 24B ADC & Quad 16B RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。