參數資料
型號： MPG5374X
元件分類： LED
英文描述： T-1 3/4 SINGLE COLOR LED, GREEN, 5 mm
封裝： ROHS COMPLIANT PACKAGE-2
文件頁數： 16/32頁
文件大?。?/td> 413K
代理商： MPG5374X
23
XMEGA C3 [DATASHEET]
8361D–AVR–07/2013
12.
System Control and Reset
12.1 Features
Reset the microcontroller and set it to initial state when a reset source goes active
Multiple reset sources that cover different situations
– Power-on reset
– External reset
– Watchdog reset
– Brownout reset
– PDI reset
– Software reset
Asynchronous operation
– No running system clock in the device is required for reset
Reset status register for reading the reset source from the application code
12.2 Overview
The reset system issues a microcontroller reset and sets the device to its initial state. This is for situations where
operation should not start or continue, such as when the microcontroller operates below its power supply rating. If a reset
source goes active, the device enters and is kept in reset until all reset sources have released their reset. The I/O pins
are immediately tri-stated. The program counter is set to the reset vector location, and all I/O registers are set to their
initial values. The SRAM content is kept. However, if the device accesses the SRAM when a reset occurs, the content of
the accessed location can not be guaranteed.
After reset is released from all reset sources, the default oscillator is started and calibrated before the device starts
running from the reset vector address. By default, this is the lowest program memory address, 0, but it is possible to
move the reset vector to the lowest address in the boot section.
The reset functionality is asynchronous, and so no running system clock is required to reset the device. The software
reset feature makes it possible to issue a controlled system reset from the user software.
The reset status register has individual status flags for each reset source. It is cleared at power-on reset, and shows
which sources have issued a reset since the last power-on.
12.3 Reset Sequence
A reset request from any reset source will immediately reset the device and keep it in reset as long as the request is
active. When all reset requests are released, the device will go through three stages before the device starts running
again:
Reset counter delay
Oscillator startup
Oscillator calibration
If another reset requests occurs during this process, the reset sequence will start over again.
12.4 Reset Sources
12.4.1 Power-on Reset
A power-on reset (POR) is generated by an on-chip detection circuit. The POR is activated when the VCC rises and
reaches the POR threshold voltage (VPOT), and this will start the reset sequence.
The POR is also activated to power down the device properly when the VCC falls and drops below the VPOT level.
The VPOT level is higher for falling VCC than for rising VCC. Consult the datasheet for POR characteristics data.
相關PDF資料
PDF描述
MPI002/TERM/RD PUSHBUTTON SWITCH, SPST, MOMENTARY-TACTILE, 0.05A, 24VDC, PANEL MOUNT
MPN-7430 300 V, SILICON, PIN DIODE
MPR3372X T-1 SINGLE COLOR LED, RED, 3 mm
MPS101A SLIDE SWITCH, SP3T, LATCHED, 0.3A, 30VDC, THROUGH HOLE-RIGHT ANGLE
MPS3414 NPN SILICON TRANSISTOR
相關代理商/技術參數
參數描述
MPG5379K 制造商:Stanley Electric Co 功能描述:LED Uni-Color Green 560nm 2-Pin Bulk 制造商:The Stanley Works 功能描述:Green 2.5 x 5 mm 24 x 18 Min 12 mcd Typical 24 mcd Diffused Through Hole LED 制造商:STANLEY 功能描述:Green 2.5 x 5 mm 24 ? x 18 ? Min 12 mcd Typical 24 mcd Diffused Through Hole LED 制造商:Stanley Electric Co 功能描述:Green 2.5 x 5 mm 24 ? x 18 ? Min 12 mcd Typical 24 mcd Diffused Through Hole LED
MPG5763X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
MPG5764X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
MPG5773X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
MPG5774X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*