參數資料
型號: MPC8313EZQADDB
廠商: Freescale Semiconductor
文件頁數: 95/99頁
文件大小: 0K
描述: MPU POWERQUICC II PRO 516-PBGA
標準包裝: 40
系列: MPC83xx
處理器類型: 32-位 MPC83xx PowerQUICC II Pro
速度: 267MHz
電壓: 0.95 V ~ 1.05 V
安裝類型: 表面貼裝
封裝/外殼: 516-BBGA 裸露焊盤
供應商設備封裝: 516-PBGAPGE(27x27)
包裝: 托盤
MPC8313E PowerQUICC II Pro Processor Hardware Specifications, Rev. 4
Freescale Semiconductor
95
24 Revision History
This table summarizes a revision history for this document.
Table 73. Document Revision History
Rev.
Number
Date
Substantive Change(s)
4
11/2011
In Table 2, added following notes:
Note 3: Min temperature is specified with TA; Max temperature is specified with TJ
Note 4: All Power rails must be connected and power applied to the MPC8313 even if the IP
interfaces are not used.
Note 5: All I/O pins should be interfaced with peripherals operating at same voltage level.
Note 6: This voltage is the input to the filter discussed in Section 22.2, “PLL Power Supply Filtering.”
and not necessarily the voltage at the AVDD pin, which may be reduced from VDD by the filter
Decoupled PCI_CLK and SYS_CLK_IN rise and fall times in Table 8. Relaxed maximum rise/fall time
of SYS_CLK_IN to 4ns.
Added a note in Table 27 stating “The frequency of RX_CLK should not exceed the TX_CLK by more
than 300 ppm."
Changed max value of tskrgt in “Data to clock input skew (at receiver)” row from 2.8 to 2.6.
Added Note 7, stating that, “The frequency of RX_CLK should not exceed the GTX_CLK125 by
more than 300 ppm.”
Added a note stating “eTSEC should be interfaced with peripheral operating at same voltage level” in
TSEC1_MDC and TSEC_MDIO are powered at 3.3V by NVDD. Replaced LVDDA/LVDDB with NVDD
and removed instances of 2.5V at several places in Section 8.5, “Ethernet Management Interface
In Table 43, changed min/max values of tCLK_TOL from 0.05 to 0.005.
Added Note 2 for LGPL4 in showing LGPL4 as open-drain.
Removed Note 2 from TSEC1_MDIO.
Added Note 10: This pin has an internal pull-up.
Added Note 11: This pin has an internal pull-down.
Added Note 12: “In MII mode, GTX_CLK should be pulled down by 300
to V
SS” to
TSEC1_GTX_CLK and TSEC2_GTX_CLK.
with "Sn/3.5 Ag."
Added foot note 3 in Table 65 stating “The VCO divider needs to be set properly so that the System
PLL VCO frequency is in the range of 450–750 MHz.”
Added AD = 266 and D = 266.
Added “C = 2.2” in “Revision level” column.
Added Note 4.
Changed resitor from 1.0
to 10 in Figure 58.
Replaced LCCR with LCRR throughout.
Added high-speed to USB Phy description.
3
01/2009
Table 72, in column aa, changed to AG = 400 MHz.
2.2
12/2008
Made cross-references active for sections, figures, and tables.
2.1
12/2008
Added Figure 2, after Table 2 and renumbered the following figures.
相關PDF資料
PDF描述
IDT7133LA20J IC SRAM 32KBIT 20NS 68PLCC
MPC8313EVRADDB MPU POWERQUICC II PRO 516-PBGA
IDT7143LA20JG IC SRAM 32KBIT 20NS 68PLCC
MPC8315EVRAFDA MPU POWERQUICC II PRO 620-PBGA
MPC8315CVRAFDA MPU POWERQUICC II PRO 620-PBGA
相關代理商/技術參數
參數描述
MPC8313EZQADDC 功能描述:微處理器 - MPU 8313 REV2.2 PB W/ENC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC8313EZQAFD 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8313EZQAFDA 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8313EZQAFDB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8313EZQAFF 功能描述:微處理器 - MPU 8313 PB PBGA W/ ENCR RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324