G-2
MPC561/MPC563 Reference Manual
MOTOROLA
66-MHz Feature Limitations
13
VSS Differential Voltage
VSS – VSSA
-0.1
0.1
V
15
VREF Differential Voltage
VRH – VRL
-5.6
5.6
V
16
V
RL
to V
SSA
Differential Voltage
V
RL
– V
SSA
-0.3
0.3
V
17
Maximum Input Current per pin 10, 11, 12
IMA
-25 13
mA
18
QADC Maximum Input Current per Pin
IMAX
mA
19
Operating Temperature Range – Ambient
(Packaged), M temperature range.
TA
-40
(TL)
+125
(TH)
°C
19a Operating Temperature Range – Ambient
(Packaged), C temperature range.
TA
-40
(TL)
+85
(TH)
°C
20
Operating Temperature Range – Solder Ball
(Packaged any perimeter solder ball) 14
TSB
-40
(TL)
+135
(TH)
°C
21
Junction Temperature Range
TJ
-40
+150
°C
22
Storage Temperature Range
TSTG
-55
+150
°C
23
Maximum Solder Temperature 15
TSDR
—235
°C
24
Moisture Sensitivity Level 16
MSL
—
3
—
1 For internal digital supply of V
DDL = 2.6-V typical.
2 2.6 volt supply pins can withstand up to 3.6 volts for acumulative time of 24 hours over the lifetime of the device.
3 During operation the value of V
FLASH must be 5.0 V ±5%
4 These power supplies are available on MPC563 and MPC564 only.
5 Maximum average current into the IRAMSTBY pin must be < 1.75mA.
6 V
DDA=5.0 V ±5%.
7 All 2.6-V input-only pins are 5-V tolerant.
8 Note that long term reliability may be compromised if 2.6-V output drivers drive a node which has been previously
pulled to >3.1 V by an external component. HRESET and SRESET are fully 5-V compatible.
9 6.35 V on 5-V only pins (all QADC, all TPU, all QSMCM and the following MIOS pins: MDA[11:15], MDA[27:31],
MPWM16, MPIO32B[7:9]/MPWM[20:21], MPIO32B11/C_CNRX0, MPIO32B12/C_CNTX0 ). Internal structures hold
the input voltage below this maximum voltage on all of these pins, except the QSMCM RXD1/QPI1 and
RXD2/QPI2/C_CNRX0 pins, if the maximum injection current specification is met (1 mA for all pins; exception: 3 mA
on QADC pins) and VDDH is within Operating Voltage specifications (see specification 43 in
Table G-4). Exception:
The RXD1/QGPI1 and RXD2/GPI2 pins do not have clamp diodes to VDDH. Voltage must be limited to less than 6.5
volts on these 2 pins to prevent damage.
10 Maximum continuous current on I/O pins provided the overall power dissipation is below the power dissipation of the
package. Proper operation is not guaranteed at this condition.
11 Condition applies to one pin at a time.
12 Transitions within the limit do not affect device reliability or cause permanent damage. Exceeding limit may cause
permanent conversion error on stressed channels and on unstressed channels.
13 Maximum transient current per ISO7637.
14 Maximum operating temperature on any solder ball in outer four rows of solder balls on the package. These rows are
referred to as “Perimeter Balls” to distinguish them from the balls in the center of the package.
15 Solder profile per CDF-AEC-Q100, current revision.
16 Moisture sensitivity per JEDEC test method J-STD-020-A (April 1999).
Table G-1. Absolute Maximum Ratings (VSS = 0V) (continued)
Rating
Symbol
Min. Value
Max. Value
Unit