參數資料
型號: MM908E626
廠商: 飛思卡爾半導體(中國)有限公司
元件分類: 基準電壓源/電流源
英文描述: Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
中文描述: 集成的步進電機驅動器,帶有嵌入式微控制器和LIN串行通信
文件頁數: 26/38頁
文件大?。?/td> 507K
代理商: MM908E626
Analog Integrated Circuit Device Data
Freescale Semiconductor
26
908E626
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Figure 14. BEMF Signal Generation
HALF-BRIDGE OVERTEMPERATURE
PROTECTION
The half-bridge outputs provide an overtemperature pre-
warning with the HTF in the Interrupt Flag Register (IFR). In
order to protect the outputs against overtemperature, the
High-Temperature Reset must be enabled. If this value is
reached, the part generates a reset and disables all power
outputs.
HALF-BRIDGE OVERCURRENT PROTECTION
The half-bridges are protected against short to GND, short
to VSUP, and load shorts.
In the event an overcurrent on the high side is detected,
the high-side MOSFETs on all HB high-side MOSFETs are
switched off automatically. In the event an overcurrent on the
low side is detected, all HB low-side MOSFETs are switched
off automatically. In both cases, the overcurrent status flag
HB_OCF in the System Status Register (SYSSTAT) is set.
The overcurrent status flag is cleared (and the outputs re-
enabled) by writing a logic [1] to the HB_OCF flag in the
System Status Register or by reset.
HALF-BRIDGE OVERVOLTAGE / UNDERVOLTAGE
The half-bridge outputs are protected against
undervoltage and overvoltage conditions. This protection is
done by the low- and high-voltage interrupt circuitry. If one of
these flags (LVF, HVF) is set, the outputs are automatically
disabled.
The overvoltage undervoltage status flags are cleared
(and the outputs re-enabled) by writing a logic [1] to the LVF /
HVF flags in the Interrupt Flag Register or by reset. Clearing
this flag is useless as long as a high- or low-voltage condition
is present.
Half-Bridge Control Register (HBCTL)
OFC_EN — H-Bridge Offset Chopping Enable Bit
This read / write bit enables offset chopping. Reset clears
the OFC_EN bit.
1 = Offset chopping enabled.
0 = Offset chopping disabled.
Coil Current
Voltage on
1
1
BEMF Signal
Register Name and Address: HBCTL - $02
Bit 7
6
5
4
3
2
1
Bit 0
Read
OFC_EN
CSA
0
0
0
CLS2
CLS1
CLS0
Write
Reset
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MMA1200D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1200 Surface Mount Micromachined Accelerometer
MMA1210D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1210 Surface Mount Micromachined Accelerometer
MMA1211D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
相關代理商/技術參數
參數描述
MM908E626AVDWB 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVPEK 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E626AVPEKR2 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT