參數資料
型號： MM908E626
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： 基準電壓源/電流源
英文描述： Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
中文描述： 集成的步進電機驅動器，帶有嵌入式微控制器和LIN串行通信
文件頁數： 15/38頁
文件大?。?/td> 507K
代理商： MM908E626
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
908E626
FUNCTIONAL DESCRIPTION
FUNCTIONAL TERMINAL DESCRIPTION
CURRENT LIMITATION FREQUENCY INPUT
TERMINAL (FGEN)
Input terminal for the half-bridge current limitation PWM
frequency. This input is not a real PWM input terminal; it
should just supply the period of the PWM. The duty cycle will
be generated automatically.
Important
The recommended FGEN frequency should
be in the range of 0.1 kHz to 20 kHz.
BACK ELECTROMAGNETIC FORCE OUTPUT
TERMINAL (BEMF)
This terminal gives the user information about back
electromagnetic force (BEMF). This feature allows stall
detection and coil failures in step motor applications. In order
to evaluate this signal the terminal must be directly connected
to terminal PTD0 TACH0 / BEMF.
RESET TERMINAL (
RST_A
)
RST_A
is the bidirectional reset terminal of the analog die.
It is an open drain with pullup resistor and must be connected
to the
RST
terminal of the MCU.
INTERRUPT TERMINAL (
IRQ_A
)
IRQ_A
is the interrupt output terminal of the analog die
indicating errors or wake-up events. It is an open drain with
pullup resistor and must be connected to the
IRQ
terminal of
the MCU.
SLAVE SELECT TERMINAL (
SS
)
This terminal is the SPI Slave Select terminal for the
analog chip. All other SPI connections are done internally.
SS
must be connected to PTB1 or any other logic I /O of the
microcontroller.
LIN BUS TERMINAL (LIN)
The LIN terminal represents the single-wire bus
transmitter and receiver. It is suited for automotive bus
systems and is based on the LIN bus specification.
HALF-BRIDGE OUTPUT TERMINALS (HB1: HB4)
The 908E626 device includes power MOSFETs
configured as four half-bridge driver outputs. The HB1: HB4
outputs may be configured for step motor drivers, DC motor
drivers, or as high-side and low-side switches.
The HB1: HB4 outputs are short-circuit and
overtemperature protected, and they feature current recopy,
current limitation, and BEMF generation. Current limitation
and recopy are done on the low-side MOSFETs.
POWER SUPPLY TERMINALS (VSUP1: VSUP3)
VSUP1: VSUP3 are device power supply terminals. The
nominal input voltage is designed for operation from 12 V
systems. Owing to the low ON-resistance and current
requirements of the half-bridge driver outputs, multiple VSUP
terminals are provided.
All VSUP terminals must be connected to get full chip
functionality.
POWER GROUND TERMINALS (GND1 AND GND2)
GND1 and GND2 are device power ground connections.
Owing to the low ON-resistance and current requirements of
the half-bridge driver outputs multiple terminals are provided.
GND1 and GND2 terminals must be connected to get full
chip functionality.
SWITCHABLE V
DD
OUTPUT TERMINAL (HVDD)
The HVDD terminal is a switchable V
DD
output for driving
resistive loads requiring a regulated 5.0 V supply; The output
is short-circuit protected.
+ 5.0 V VOLTAGE REGULATOR OUTPUT
TERMINAL (VDD)
The VDD terminal is needed to place an external capacitor
to stabilize the regulated output voltage. The VDD terminal is
intended to supply the embedded microcontroller.
Important
The VDD terminal should not be used to
supply other loads; use the HVDD terminal for this purpose.
The VDD, EVDD, VDDA, and VREFH terminals must be
connected together.
VOLTAGE REGULATOR GROUND TERMINAL
(VSS)
The VSS terminal is the ground terminal for the connection
of all non-power ground connections (microcontroller and
sensors).
Important
VSS, EVSS, VSSA, and VREFL terminals
must be connected together.
LIN TRANSCEIVER OUTPUT TERMINAL (RXD)
This terminal is the output of LIN transceiver. The terminal
must be connected to the microcontroller’s Enhanced Serial
Communications Interface (ESCI) module (RXD terminal).
ADC REFERENCE TERMINALS (VREFL AND
VREFH)
VREFL and VREFH are the reference voltage terminals for
the ADC. It is recommended that a high-quality ceramic
decoupling capacitor be placed between these terminals.
Important
VREFH is the high reference supply for the
ADC and should be tied to the same potential as VDDA via
separate traces. VREFL is the low reference supply for the
ADC and should be tied to the same potential as VSS via
separate traces.
For details refer to the 68HC908EY16 datasheet.
相關PDF資料
PDF描述
MMA1200D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1200 Surface Mount Micromachined Accelerometer
MMA1210D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1210 Surface Mount Micromachined Accelerometer
MMA1211D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
相關代理商/技術參數
參數描述
MM908E626AVDWB 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVPEK 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E626AVPEKR2 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*