參數資料
型號: MM908E626
廠商: 飛思卡爾半導體(中國)有限公司
元件分類: 基準電壓源/電流源
英文描述: Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
中文描述: 集成的步進電機驅動器,帶有嵌入式微控制器和LIN串行通信
文件頁數: 19/38頁
文件大?。?/td> 507K
代理商: MM908E626
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
908E626
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
RESET INTERNAL SOURCES
Autonomous Watchdog
AWD modules generates a reset because of a timeout
(watchdog function).
High-Temperature Reset
To prevent damage to the device, a reset will be initiated if
the temperature rises above a certain value. The reset is
maskable with bit HTRE in the Reset Mask Register. After a
reset the high-temperature reset is disabled.
Low-Voltage Reset
The LVR is related to the internal V
DD
. In case the voltage
falls below a certain threshold, it will pull down the
RST_A
terminal.
High-Voltage Reset
The HVR is related to the external V
SUP
voltage. In case
the voltage is above a certain threshold, it will pull down the
RST_A
terminal. The reset is maskable with bit HVRE in the
Reset Mask Register. After a reset the high-voltage reset is
disabled.
RESET
EXTERNAL SOURCE
External
Reset Terminal
The microcontroller has the capability of resetting the
SMARTMOS
device by pulling down the
RST
terminal.
Reset Mask Register (RMR)
TTEST
High-Temperature Reset Test
This read / write bit is for test purposes only. It decreases
the overtemperature shutdown limit for final test. Reset clears
the HTRE bit.
1 = Low-temperature threshold enabled.
0 = Low-temperature threshold disabled.
HVRE
High-Voltage Reset Enable Bit
This read / write bit enables resets on high-voltage
conditions. Reset clears the HVRE bit.
1 = High-voltage reset enabled.
0 = High-voltage reset disabled.
HTRE
High-Temperature Reset Enable Bit
This read / write bit enables resets on high-temperature
conditions. Reset clears the HTRE bit.
1 = High-temperature reset enabled.
0 = High-temperature reset disabled.
SERIAL PERIPHERAL INTERFACE
The serial peripheral interface (SPI) creates the
communication link between the microcontroller and the
908E626.
The interface consists of four terminals (see
Figure 10
):
SS
— Slave Select
MOSI — Master-Out Slave-In
MISO — Master-In Slave-Out
SPSCK — Serial Clock (maximum frequency 4.0 MHz)
A complete data transfer via the SPI consists of 2 bytes.
The master sends address and data, slave system status,
and data of the selected address.
Register Name and Address: RMR - $06
Bit 7
6
5
4
3
2
1
Bit 0
Read
TTEST
0
0
0
0
0
HVRE
HTRE
Write
Reset
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MMA1200D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1200 Surface Mount Micromachined Accelerometer
MMA1210D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1210 Surface Mount Micromachined Accelerometer
MMA1211D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
相關代理商/技術參數
參數描述
MM908E626AVDWB 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVPEK 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E626AVPEKR2 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT