- 您現在的位置：買賣IC網 > Datasheet目錄44 > MIC2585-2MBTS TR (Micrel Inc)IC CTRLR HOT SWAP DUAL 24-TSSOP Datasheet資料下載
參數資料
| 型號： | MIC2585-2MBTS TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 22/28頁 |
| 文件大?。?/td> | 273K |
| 描述： | IC CTRLR HOT SWAP DUAL 24-TSSOP |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 1 V ~ 13.2 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | MIC2585-2MBTSTR MIC2585-2MBTSTR-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MIC2584/2585
Micrel
MIC2584/2585
22
March 2005
Higher UVLO Setting
Once a PCB is inserted into a backplane (power supply), the
internal UVLO circuit of the MIC2584/85 holds the GATE
output charge pump off until VCC1 exceeds 2.165V and
VCC2 exceeds 0.8V. If VCC1 falls below 1.935V or VCC2
falls below 0.77V, the UVLO circuit pulls the GATE output to
ground and clears the overvoltage and/or current limit faults.
For a higher UVLO threshold, the circuit in Figure 10 can be
used to delay the output MOSFET from switching on until the
desired input voltage is achieved. The circuit allows the
charge pumps to remain off until V
IN1
exceeds
1
R1
R2
1.235V
+
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
provided that VCC2 has exceeded its
threshold. Both GATE drive outputs will be shut down when
V
IN1
falls below
1
R1
R2
1.21V
+
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
. In the example circuit , the
rising UVLO threshold is set at approximately 9.0V and the
falling UVLO threshold is established as 8.9V. The circuit
consists of an external resistor divider at the ON pin that
keeps both GATE output charge pumps off until the voltage
at the ON pin exceeds its threshold (V
ON
) and after the start-
up timer elapses.
Hot Swap Power Control for DSPs
In designing power supplies for dual supply logic devices,
such as a DSP, consideration should be given to the system
timing requirements of the core and I/O voltages for power-
up and power-down operations. When power is provided to
the core and I/O circuit blocks in an unpredictable manner,
the effects can be detrimental to the life cycle of the DSP or
logic device by allowing unexpected current to flow in the core
and I/O isolation structures. Additionally, bus contention is
one of the critical system-level issues supporting the need for
power supply sequencing. Since the core supplies logic
control for the bus, powering up the I/O before the core may
result in both the DSP and an attached peripheral device
being simultaneously configured as outputs. In this case, the
output drivers of each device contend for control over sending
data along the bus which may cause excessive current to flow
in one of the paths (I
1
or I
2
) shown in the bidirectional port of
Figure 11. Upon powering down the system, the core voltage
supply should turn off after the I/O as the bus control signal(s)
may enter an indeterminate state if the core is powered down
first. Thus, for power sequencing of a dual supply voltage
DSP implementing the MIC2585 (if V
CORE
e V
I/O
), a circuit
similar to Figure 8 is recommended with the core voltage
supplied through Channel 1 and the I/O voltage supplied
through Channel 2. For systems with V
CORE
< V
I/O
, the
MIC2585-2 option with the I/O voltage through Channel 1 and
core through Channel 2 is used to implement the first on-last
off application.
Sense Resistor Selection
The MIC2584 and MIC2585 use a low-value sense resistor to
measure the current flowing through the MOSFET switch
(and therefore the load). This sense resistor is nominally set
at 50mV/I
LOAD(CONT)
. To accommodate worst-case toler-
ances for both the sense resistor (allow ?% over time and
temperature for a resistor with ?% initial tolerance) and still
supply the maximum required steady-state load current, a
slightly more detailed calculation must be used.
The current limit threshold voltage (i.e., the trip point ) for the
MIC2584/85 may be as low as 42.5mV, which would equate
to a sense resistor value of 42.5mV/I
LOAD(CONT)
. Carrying the
numbers through for the case where the value of the sense
resistor is 3% high yields:
R
42.5mV
1.03 I
41.3mV
I
SENSE(MAX)
LOAD(CONT)
LOAD(CONT)
=
( )
(
)
=
(11)
Once the value of R
SENSE
has been chosen in this manner,
it is good practice to check the maximum I
LOAD(CONT)
which
the circuit may let through in the case of tolerance build-up in
SENSE1
VCC1
ON
FB1
GATE1
GND
Undervoltage Lockout Threshold (rising) = 9.0V
Undervoltage Lockout Threshold (falling) = 8.9V
Undervoltage (Output) = 11.4V
Channel 2 and additional pins omitted for clarity.
Q1
IRF7822
(SO-8)
R3
10&
R5
16.2k&
1%
R1
154k&
1%
R2
24.3k&
1%
MIC2584
C1
1礔
D1
(18V)
C2
0.01礔
C
LOAD1
1000礔
R4
133k&
1%
V
OUT1
12V@4A
V
IN1
12V
9
16
15
12
6
14
R
SENSE1
0.010&
5%
1
2
3
4
Figure 10. Higher UVLO Setting
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2586R-2BM TR | IC CTRLR/SEQ HOT SWAP 14-SOIC |
| MIC2587R-2BM TR | IC CTRLR HOT SWAP POS HV 8-SOIC |
| MIC2590B-5BTQ TR | IC PCI HOT PLUG CTLR DUAL 48TQFP |
| MIC2591B-2BTQ TR | IC PCI HOT PLUG CTLR DUAL 48TQFP |
| MIC2592B-2BTQ TR | IC PCI HOT PLUG CTLR DUAL 48TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2586-1BM | 功能描述:IC CTRLR/SEQ HOT SWAP 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2586-1BM TR | 功能描述:IC CTRLR/SEQ HOT SWAP 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2586-1YM | 功能描述:熱插拔功率分布 Positive High Voltage Hot-Swap Controller/Sequencer - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2586-1YM TR | 功能描述:熱插拔功率分布 Positive High Voltage Hot-Swap Controller/Sequencer - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2586-2BM | 功能描述:IC CTRLR/SEQUENCE HOTSWAP 14SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發(fā)布緊急采購，3分鐘左右您將得到回復。