- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33991EG (飛思卡爾半導體(中國)有限公司) Gauge Driver Integrated Circuit PDF資料下載
參數資料
| 型號： | MCZ33991EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Gauge Driver Integrated Circuit |
| 中文描述： | 儀表驅動集成電路 |
| 文件頁數： | 28/36頁 |
| 文件大?。?/td> | 481K |
| 代理商： | MCZ33991EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
28
33991
TIMING DESCRIPTIONS AND DIAGRAMS
APPLICATION INFORMATION
Table 18. 33991 Setup, Configuration, & Usage Example
Step #
Command
Description
Reference
Figure #
1
PECR
a.
- Bit PE0: Gauge 0.
- Bit PE1: Gauge 1.
Enable Gauges.
Table 3
Figure 7
b.
- Bit PE3: Enables Calibration Procedure.
- Bit PE4: Set clock f =1 MHz maximum or nominal.
Clock Calibration.
Send 8
μ
s pulse on CS to calibrate 1 MHz clock.
2
RTZCR
Set RTZ Full Step Time.
- Bits RC3:RC0.
Tables 9-10
Set RTZ Blanking Time.
- Bit RC4.
Tables 9-10
Preload RTZ Accumulator.
- Bits RC12:RC5.
Table 11
Check SO for an Out-of-Range Clock Calibration
- Is bit ST7 logic 1 If so, then repeat Steps 1 and 2.
Table 12
3
POS0R
a.
Move pointer to position 24 prior to RTZ
Table 5
4
POS1R
Move pointer to position 24 prior to RTZ.
Table 6
Check SO to see if gauge 0 has moved.
- Is bit ST4 logic 1 If so then the gauge 0 has moved to the first microstep.
Table 12
5
PECR
Send null command to see if gauges have moved.
- Bits PE12.
Table 3
Check SO to see if Gauge 0 (Gauge 1) has moved.
- Bit ST4 (ST5) logic1 If so, then gauge 0 (Gauge 1) has moved another microstep.
Keep track of movement and if 24 steps are finished, and both gauges are at a static
position, then RTZ. Otherwise repeat steps a) and b).
Table 12
6
RTZ
a.
RTZ command Bit RZ0 selects the gauge Bit RZ1 is used to enable or disable an
RTZ.
- Bits RZ3:RZ2 are used to select the RTZ accumulator bits that will clock out on the
SO pin.
Return one gauge at a time to the zero stop using
Table 7
b.
out on the SO bits ST15:ST8. These will be used if characterizing the RTZ.
- Bits RZ3:RZ2 are used to select the bits.
Select the RTZ accumulator bits that will clock
Table 8
7
PECR
a.
command to monitor SO bit ST2.
- Bit PE12 is the null command.
Check the Status of the RTZ by sending the null
Table 3
Is ST2 logic 0 If not then gauge 0 still returning and null command should be resent.
Table 12
8
RTZ
Return the other gauge to the zero stop. If the second gauge is driving a different
pointer than the first, then a new RTZCR command may be required to change the
Full Step time.
Tables 7-8
9
PECR
a.
command to monitor SO bit ST3
- Bit PE12 is the null command.
Check the Status of the RTZ by sending the null
Table 3
Is ST3 logic 0 If not then gauge 1 still returning and null command should be resent.
Table 12
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33993EW | Multiple Switch Detection Interface |
| MCZ33996EK | 16-Output Switch with SPI Control |
| MCZ34652EF | 2.0 A Negative Voltage Hot Swap Controller with Enhanced Programmability |
| MCZ34701EWR2 | 1.5A Switch-Mode Power Supply with Linear Regulator |
| MCZ79076EG | Electronic Ignition Control Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33991EGR2 | 功能描述:馬達/運動/點火控制器和驅動器 GAUGE DRIVER IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33993EW | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MCZ33993EWR2 | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MCZ33996CEK | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Bulk |
| MCZ33996CEKR2 | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。