- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33991EG (飛思卡爾半導體(中國)有限公司) Gauge Driver Integrated Circuit PDF資料下載
參數資料
| 型號： | MCZ33991EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Gauge Driver Integrated Circuit |
| 中文描述： | 儀表驅動集成電路 |
| 文件頁數： | 19/36頁 |
| 文件大小： | 481K |
| 代理商： | MCZ33991EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33991
TIMING DESCRIPTIONS AND DIAGRAMS
DEVICE FUNCTIONAL DESCRIPTION
0 = Gauge 1 position has not changed since the last SPI
command
1 = Gauge 1 pointer position has changed since the last
SPI command
ST4–Gauge 0— Movement since last SPI communication.
A logic [1] on this bit indicates the Gauge 0 pointer position
has changed since the last SPI command. The master
confirms that the pointer is moving as commanded.
0 = Gauge 0 position has not changed since the last SPI
command
1 = Gauge 0 pointer position has changed since the last
SPI command
ST3–RTZ1—Enabled successful or disabled. A logic [1]
on this bit indicates Gauge 1 is in the process of returning to
the zero position as requested with the RTZ command. This
bit continues to indicate a logic [1] until the SPI message
following a detection of the zero position, or the RTZ feature
is commanded OFF using the RTZ message.
0 = Return to Zero disabled
1 = Return to Zero enabled successful
ST2–RTZ0—Enabled successful or disabled. A logic [1]
on this bit indicates Gauge 0 is in the process of returning to
the zero position as requested with the RTZ command. This
bit continues indicating a logic [1] until the SPI message
following a detection of the zero position, or the RTZ feature
is commanded OFF, using the RTZ message.
0 = Return to Zero disabled
1 = Return to Zero enabled successful
ST1–Gauge 1 Junction over temperature. A logic [1] on
this bit indicates coil drive circuitry dedicated to drive Gauge
1 exceeded the maximum allowable junction temperature
since the last SPI communication. Additionally, the same
indication signals the circuitry Gauge 1 is disabled. It is
recommended the pointer be re-calibrated using the RTZ
command after re-enabling the gauge using the PECR
command. This bit remains logic [1] until the gauge is
enabled.
0 = Temperature within range
1 = Gauge 1 maximum allowable junction temperature
condition has been reached
ST0–Gauge 0— Junction over temperature. A logic [1] on
this bit indicates coil drive circuitry dedicated to drive Gauge
0 exceeded the maximum allowable junction temperature
since the last SPI communication. Additionally, the same
indication signals the circuitry Gauge 0 is disabled. It is
recommended the pointer be re-calibrated using the RTZ
command after re-enabling the gauge, using the PECR
command. This bit remains logic [1] until the gauge is re-
enabled.
0 = Temperature within range
1 = Gauge 0 maximum allowable junction temperature
condition has been reached
DEVICE FUNCTIONAL DESCRIPTION
STATE MACHINE OPERATION
The two-phase stepper motor is defined as maximum
velocity and acceleration, and deceleration. It is the purpose
of the stepper motor state machine is to drive the motor with
maximum performance, while remaining within the motor’s
velocity and acceleration constraints.
When commanded, the motor should accelerate
constantly to the maximum velocity, then decelerate and stop
at the desired position. During the deceleration phase, the
motor should not exceed the maximum deceleration. A
required function of the state machine is to ensure the
deceleration phase begins at the correct time, or position.
During normal operation, both stepper motor rotors are
microstepped with 24 steps per electrical revolution. See
Figure 6. A complete electrical revolution results in two
degrees of pointer movement. There is a second and smaller
state machine in the IC controlling these microsteps. This
state machine receives
clockwise
or
counter-clockwise
index
commands at intervals, stepping the motor in the appropriate
direction by adjusting the current in each coil. Normalized
values provided in Table 13.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33993EW | Multiple Switch Detection Interface |
| MCZ33996EK | 16-Output Switch with SPI Control |
| MCZ34652EF | 2.0 A Negative Voltage Hot Swap Controller with Enhanced Programmability |
| MCZ34701EWR2 | 1.5A Switch-Mode Power Supply with Linear Regulator |
| MCZ79076EG | Electronic Ignition Control Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33991EGR2 | 功能描述:馬達/運動/點火控制器和驅動器 GAUGE DRIVER IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33993EW | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MCZ33993EWR2 | 功能描述:接口 - 專用 MSDI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MCZ33996CEK | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Bulk |
| MCZ33996CEKR2 | 制造商:Freescale Semiconductor 功能描述:16 LOW SIDE SW - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。