Analog Output Voltage Pin (VOUT
參數資料
型號： MCP4716A0T-E/MAY
廠商： Microchip Technology
文件頁數： 28/86頁
文件大?。?/td> 0K
描述： IC DAC 10BIT NV EEP I2C 6DFN
標準包裝： 1
設置時間： 6µs
位數： 10
數據接口： EEPROM，I²C，串行
轉換器數目： 1
電壓電源： 單電源
功率耗散（最大）： 1.10W
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 6-VDFN 裸露焊盤
供應商設備封裝： 6-DFN（2x2）
包裝： 標準包裝
輸出數目和類型： 1 電壓，單極
采樣率（每秒）： *
其它名稱： MCP4716A0T-E/MAYDKR
MCP4706/4716/4726
DS22272C-page 34
2011-2012 Microchip Technology Inc.
3.1
Analog Output Voltage Pin (VOUT)
VOUT is the DAC analog output pin. The DAC output
has an output amplifier. VOUT can swing from
approximately 0V to approximately VDD. The full-scale
range of the DAC output is from VSS to G * VRL, where
G is the gain selection option (1x or 2x).
In Normal mode, the DC impedance of the output pin is
about 1
Ω. In Power-Down mode, the output pin is
internally connected to a known pull-down resistor of
1k
Ω, 125 kΩ, or 640 kΩ. The power-down selection
bits settings are shown in Table 4-2.
3.2
Positive Power Supply Input (VDD)
VDD is the positive supply voltage input pin. The input
supply voltage is relative to VSS.
The power supply at the VDD pin should be as clean as
possible
for
a
good
DAC
performance.
It
is
recommended to use an appropriate bypass capacitor
of about 0.1 F (ceramic) to ground. An additional
10 F
capacitor
(tantalum)
in
parallel
is
also
recommended to further attenuate high-frequency
noise present in application boards.
3.3
Ground (VSS)
The VSS pin is the device ground reference.
The user must connect the VSS pin to a ground plane
through a low-impedance connection. If an analog
ground path is available in the application Printed
Circuit Board (PCB), it is highly recommended that the
VSS pin be tied to the analog ground path or isolated
within an analog ground plane of the circuit board.
3.4
Serial Data Pin (SDA)
SDA is the serial data pin of the I2C interface. The SDA
pin is used to write or read the DAC registers and Con-
figuration bits. The SDA pin is an open-drain N-channel
driver. Therefore, it needs a pull-up resistor from the
VDD line to the SDA pin. Except for Start and Stop
conditions, the data on the SDA pin must be stable
during the high period of the clock. The high or low
state of the SDA pin can only change when the clock
signal on the SCL pin is low. Refer to Section 5.0 “I2C
Serial Interface” for more details of I2C serial interface
communication.
3.5
Serial Clock Pin (SCL)
SCL is the serial clock pin of the I2C interface. The
MCP47X6 devices act only as a slave and the SCL pin
accepts only external serial clocks. The input data from
the master device is shifted into the SDA pin on the
rising edges of the SCL clock and output from the
device occurs at the falling edges of the SCL clock. The
SCL pin is an open-drain N-channel driver. Therefore,
it needs a pull-up resistor from the VDD line to the SCL
more details about I2C serial interface communication.
3.6
Voltage Reference Pin (VREF)
This pin is used for the external voltage reference input.
The user can select VDD voltage or the VREF pin
voltage as the reference resistor ladder’s voltage
reference.
When the VREF pin signal is selected, there is an option
for this voltage to be buffered or unbuffered. This is
offered in cases where the reference voltage does not
have the current capability not to drop its voltage when
connected to the internal resistor ladder circuit.
When the VDD is selected as reference voltage, this pin
is disconnected from the internal circuit.
See
Reference Voltage” and Table 4-4 for more details on
the Configuration bits.
3.7
Exposed Pad (EP)
This pad is conductively connected to the device's
substrate. This pad should be tied to the same potential
as the VSS pin (or left unconnected). This pad could be
used to assist as a heat sink for the device when
connected to a PCB heat sink.
相關PDF資料
PDF描述
M83723/74W2232Y CONN RCPT 32POS JAM NUT W/PINS
VI-BT4-MY-F4 CONVERTER MOD DC/DC 48V 50W
M83723/74W22328 CONN RCPT 32POS JAM NUT W/PINS
VE-22R-MW-F4 CONVERTER MOD DC/DC 7.5V 100W
VE-22R-MW-F3 CONVERTER MOD DC/DC 7.5V 100W
相關代理商/技術參數
參數描述
MCP4716A1T-E/CH 功能描述:數模轉換器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4716A1T-E/MAY 功能描述:數模轉換器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4716A2T-E/CH 功能描述:數模轉換器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4716A2T-E/MAY 功能描述:數模轉換器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
MCP4716A3T-E/CH 功能描述:數模轉換器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*