參數資料
型號： ADSP-21479KBCZ-2A
廠商： Analog Devices Inc
文件頁數： 6/72頁
文件大小： 0K
描述： IC DSP SHARC 266MHZ LP 196CSPBGA
標準包裝： 1
系列： SHARC®
類型： 浮點
接口： DAI，DPI，EBI/EMI，I²C，SPI，SPORT，UART/USART
時鐘速率： 266MHz
非易失內存： ROM（4Mb）
芯片上RAM： 5Mb
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.20V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 196-LFBGA，CSPBGA
供應商設備封裝： 196-CSPBGA（12x12）
包裝： 托盤
Rev. A
|
Page 14 of 72
|
September 2011
PIN FUNCTION DESCRIPTIONS
Table 10. Pin Descriptions
Name
Type
State During/
After Reset
Description
ADDR23–0
I/O/T (ipu)
High-Z/Driven
Low (Boot)
External Address. The processor outputs addresses for external memory and
peripherals on these pins. The ADDR pins can be multiplexed to support the
external memory interface address, FLAGS15–8 (I/O) and PWM (O). After reset, all
ADDR pins are in EMIF mode, and FLAG(0–3) pins are in FLAGS mode (default).
When configured in the IDP_PDAP_CTL register, IDP channel 0 scans the ADDR23–4
pins for parallel input data.
DATA15–0
I/O/T (ipu)
High-Z
External Data. The data pins can be multiplexed to support the external memory
interface data (I/O) and FLAGS7–0 (I/O).
AMI_ACK
I (ipu)
Memory Acknowledge. External devices can deassert AMI_ACK (low) to add wait
states to an external memory access. AMI_ACK is used by I/O devices, memory
controllers, or other peripherals to hold off completion of an external memory
access.
MS0–1
O/T (ipu)
High-Z
Memory Select Lines 0–1. These lines are asserted (low) as chip selects for the
corresponding banks of external memory. The MS1-0 lines are decoded memory
address lines that change at the same time as the other address lines. When no
external memory access is occurring the MS1-0 lines are inactive; they are active
however when a conditional memory access instruction is executed, whether or
not the condition is true.
The MS1 pin can be used in EPORT/FLASH boot mode. For more information on
processor booting, see the ADSP-214xx SHARC Processor Hardware Reference.
AMI_RD
O/T (ipu)
High-Z
AMI Port Read Enable. AMI_RD is asserted whenever the processor reads a word
from external memory.
AMI_WR
O/T (ipu)
High-Z
AMI Port Write Enable. AMI_WR is asserted when the processor writes a word to
external memory.
FLAG0/IRQ0
I/O (ipu)
FLAG[0] INPUT
FLAG0/Interrupt Request0.
FLAG1/IRQ1
I/O (ipu)
FLAG[1] INPUT
FLAG1/Interrupt Request1.
FLAG2/IRQ2/MS2
I/O (ipu)
FLAG[2] INPUT
FLAG2/Interrupt Request2/Memory Select2. This pin is multiplexed with MS2
in the 196-ball BGA package only.
FLAG3/TMREXP/MS3
I/O (ipu)
FLAG[3] INPUT
FLAG3/Timer Expired/Memory Select3. This pin is multiplexed with MS3 in the
196-ball BGA package only.
The following symbols appear in the Type column of Table 10: A = asynchronous, I = input, O = output, S = synchronous, A/D = active drive,
O/D = open drain, and T = three-state, ipd = internal pull-down resistor, ipu = internal pull-up resistor.
The internal pull-up (ipu) and internal pull-down (ipd) resistors are designed to hold the internal path from the pins at the expected logic
levels. To pull-up or pull-down the external pads to the expected logic levels, use external resistors. Internal pull-up/pull-down resistors
cannot be enabled/disabled and the value of these resistors cannot be programmed. The range of an ipu resistor can be 26 kΩ to 63 kΩ. The
range of an ipd resistor can be 31 kΩ to 85 kΩ. The three-state voltage of ipu pads will not reach to full the VDD_EXT level; at typical conditions
the voltage is in the range of 2.3 V to 2.7 V.
In this table, all pins are LVTTL compliant with the exception of the thermal diode, shift register, and real-time clock (RTC) pins.
Not all pins are available in the 100-lead LQFP package. For more information, see Table 2 on Page 3 and Table 59 on Page 64.
相關PDF資料
PDF描述
HMM36DRKF-S13 CONN EDGECARD 72POS .156 EXTEND
GMM43DSEF-S13 CONN EDGECARD 86POS .156 EXTEND
HWS150-3/A PWR SUP IND 3.3V 30A SNG OUTPUT
HWS150-5/A PWR SUP IND 5V 30A SNG OUTPUT
MAX6514UKP035+T IC TEMP SWITCH SOT23-5
相關代理商/技術參數
參數描述
MCP42100T-I/SL 功能描述:數字電位計 IC 256 Step SPI 100kOhm RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP42100T-I/ST 功能描述:數字電位計 IC 256 Step SPI 100kOhm RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4231-103E/ML 功能描述:數字電位計 IC Digital Pot 128 step SPI dual Ch RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4231-103E/P 功能描述:數字電位計 IC Dual 7B V SPI POT RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
MCP4231-103-E/P 功能描述:數字電位計 IC Digital Pot, 128 steps, SPI, dual channel RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*