- 您現在的位置：買賣IC網 > PDF目錄9324 > MCP41050T-I/SN (Microchip Technology)IC POT DIGITAL 50K 1CH SPI 8SOIC PDF資料下載
參數資料
| 型號： | MCP41050T-I/SN |
| 廠商： | Microchip Technology |
| 文件頁數： | 6/28頁 |
| 文件大小： | 0K |
| 描述： | IC POT DIGITAL 50K 1CH SPI 8SOIC |
| 標準包裝： | 3,300 |
| 接片： | 256 |
| 電阻（歐姆）： | 50k |
| 電路數： | 1 |
| 溫度系數： | 標準值 800 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 3 線串行（芯片選擇） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOICN |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MCP41XXX/42XXX
DS11195C-page 14
2003 Microchip Technology Inc.
4.1
Modes of Operation
Digital potentiometer applications can be divided into
two categories: rheostat mode and potentiometer, or
voltage divider, mode.
4.1.1
RHEOSTAT MODE
In the rheostat mode, the potentiometer is used as a
two-terminal resistive element. The unused terminal
should be tied to the wiper, as shown in Figure 4-2.
Note that reversing the polarity of the A and B terminals
will not affect operation.
FIGURE 4-2:
Two-terminal or rheostat
configuration for the digital potentiometer. Acting
as a resistive element in the circuit, resistance is
controlled by changing the wiper setting.
Using the device in this mode allows control of the total
resistance between the two nodes. The total measured
resistance would be the least at code 00h, where the
wiper is tied to the B terminal. The resistance at this
code is equal to the wiper resistance, typically 52
for
the 10 k
MCP4X010 devices, 125 for the 50 k
(MCP4X050), and 100 k
(MCP4X100) devices. For
the 10 k
device, the LSB size would be 39.0625
(assuming 10 k
total resistance). The resistance
would then increase with this LSB size until the total
measured resistance at code FFh would be 9985.94
.
The wiper will never directly connect to the A terminal
of the resistor stack.
In the 00h state, the total resistance is the wiper resis-
tance. To avoid damage to the internal wiper circuitry in
this configuration, care should be taken to ensure the
current flow never exceeds 1 mA.
For dual devices, the variation of channel-to-channel
matching of the total resistance from A to B is less than
1%. The device-to-device matching, however, can vary
up to 30%. In the rheostat mode, the resistance has a
positive temperature coefficient. The change in wiper-
to-end terminal resistance over temperature is shown
in Figure 2-8. The most variation over temperature will
occur in the first 6% of codes (code 00h to 0Fh) due to
the wiper resistance coefficient affecting the total resis-
tance. The remaining codes are dominated by the total
resistance tempco RAB, typically 800 ppm/°C.
4.1.2
POTENTIOMETER MODE
In the potentiometer mode, all three terminals of the
device are tied to different nodes in the circuit. This
allows the potentiometer to output a voltage propor-
tional to the input voltage. This mode is sometimes
called voltage divider mode. The potentiometer is used
to provide a variable voltage by adjusting the wiper
position between the two endpoints as shown in
Figure 4-3. Note that reversing the polarity of the A and
B terminals will not affect operation.
FIGURE 4-3:
Three terminal or voltage
divider mode.
In this configuration, the ratio of the internal resistance
defines the temperature coefficient of the device. The
resistor matching of the RWB resistor to the RAB resistor
performs with a typical temperature coefficient of
1 ppm/°C (measured at code 80h). At lower codes, the
wiper resistance temperature coefficient will dominate.
Figure 2-3 shows the effect of the wiper. Above the
lower codes, this figure shows that 70% of the states
will typically have a temperature coefficient of less than
5 ppm/°C. 30% of the states will typically have a
ppm/°C of less than 1.
A
B
W
MCP4XXXX
Resistor
A
B
W
MCP4XXXX
V1
V2
相關PDF資料 |
PDF描述 |
|---|---|
| DS1743P-70 | IC RTC RAM Y2K 5V 70NS 34-PCM |
| VE-BNT-IU-F4 | CONVERTER MOD DC/DC 6.5V 200W |
| VE-BNT-IU-F3 | CONVERTER MOD DC/DC 6.5V 200W |
| DS1286I | IC TIMEKEEPER WATCHDOG 28-EDIP |
| DS1244YP-70 | IC NVSRAM 256KBIT 70NS 34PCM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP41100 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI⑩ Interface |
| MCP41100E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI Interface |
| MCP41100-E/P | 功能描述:數字電位計 IC 256 Step SPI 100kOhm RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MCP41100E/SL | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI Interface |
| MCP41100E/SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI Interface |
發布緊急采購，3分鐘左右您將得到回復。