- 您現在的位置：買賣IC網 > PDF目錄10474 > MCP3422A0T-E/SN (Microchip Technology)IC ADC 18BIT 3.75SPS 2CH 8-SOIC PDF資料下載
參數資料
| 型號： | MCP3422A0T-E/SN |
| 廠商： | Microchip Technology |
| 文件頁數： | 13/58頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 18BIT 3.75SPS 2CH 8-SOIC |
| 產品培訓模塊： | MCP3901 Analog Front End |
| 標準包裝： | 3,300 |
| 位數： | 18 |
| 采樣率（每秒）： | 3.75 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOICN |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，雙極；2 個差分，雙極 |
| 配用： | MCP3422EV-ND - BOARD EVAL MCP3422 PICKIT SERIAL |
| 其它名稱： | MCP3422A0T-E/SNTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
MCP3422/3/4
DS22088C-page 20
2009 Microchip Technology Inc.
FIGURE 5-1:
Address Byte.
5.3.2
DEVICE ADDRESS BITS (A2, A1, A0)
AND ADDRESS SELECTION PINS
(MCP3423 AND MCP3424)
The MCP3423 and MCP3424 have two external
device address pins (Adr1, Adr0). These pins can be
set to a logic high (or tied to VDD), low (or tied to VSS),
or left floating (not connected to anything, or tied to
VDD/2), These combinations of logic level using the
two pins allow eight possible addresses. Table 5-3
shows the device address depending on the logic
status of the address selection pins.
The device samples the logic status of the Adr0 and
Adr1 pins in the following events:
a.
Device power-up.
b.
General Call Reset
(See Section 5.4 “General Call”).
c.
General Call Latch
(See Section 5.4 “General Call”).
The device samples the logic status (address pins)
during the above events, and latches the values until a
new latch event occurs. During normal operation (after
the address pins are latched), the address pins are
internally disabled from the rests of the internal circuit.
It is recommended to issue a General Call Reset or
General Call Latch command once after the device
has powered up. This will ensure that the device reads
the address pins in a stable condition, and avoid
latching the address bits while the power supply is
ramping up. This might cause inaccurate address pin
detection.
When the address pin is left “floating”:
When the address pin is left “floating”, the address pin
momentarily outputs a short pulse with an amplitude of
about VDD/2 during the latch event. The device also
latches this pin voltage at the same time.
If the “floating” pin is connected to a large parasitic
capacitance (>20 pF) or to a long PCB trace, this short
floating voltage output can be altered. As a result, the
device may not latch the pin correctly.
It is strongly recommended to keep the “floating” pin
pad as short as possible in the customer application
PCB and minimize the parasitic capacitance to the pin
as small as possible (< 20 pF).
Figure 5-2 shows an example of the Latch voltage
output at the address pin when the address pin is left
“floating”. The waveform at the Adr0 pin is captured by
using an oscilloscope probe with 15 pF of capacitance.
The device latches the floating condition immediately
after the General Call Latch command.
FIGURE 5-2:
General Call Latch
Command and Voltage Output at Address Pin
Left “Floating” (MCP3423 and MCP3424).
Start bit
Read/Write bit
Address Byte
R/W ACK
1
0
1
A2
A1
A0
Device Code
Address Bits (Note 1)
Address Byte:
Acknowledge bit
Address
Note
1:
MCP3423 and MCP3424: Configured by
the user. See Table 5-3 for address bit
configurations.
2:
MCP3422: Programmed at the factory
during production.
Float waveform (output)
at address pin
SCL
SDA
相關PDF資料 |
PDF描述 |
|---|---|
| MCP3427T-E/UN | IC ADC 16BIT I2C PROGBL 10-MSOP |
| VE-24H-IW-F2 | CONVERTER MOD DC/DC 52V 100W |
| VE-J5V-MW-F4 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-BVJ-MX-F4 | CONVERTER MOD DC/DC 36V 75W |
| VE-BVJ-MX-F2 | CONVERTER MOD DC/DC 36V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3422A1-E/MC | 功能描述:模數轉換器 - ADC MULTI-CHANNEL 18 BIT DEL SIG A/D CONVERT RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3422A1-E/MF | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3422A1-E/MS | 功能描述:模數轉換器 - ADC MULTI-CHANNEL 18 BIT DEL SIG A/D CONVERT RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3422A1-E/SL | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3422A1-E/SN | 功能描述:模數轉換器 - ADC MULTI-CHANNEL 18 BIT DEL SIG A/D CONVERT RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。