- 您現在的位置：買賣IC網 > PDF目錄16673 > MCP2150DM (Microchip Technology)BOARD DEMO FOR MCP2150 PDF資料下載
參數資料
| 型號： | MCP2150DM |
| 廠商： | Microchip Technology |
| 文件頁數： | 52/52頁 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO FOR MCP2150 |
| 標準包裝： | 1 |
| 主要目的： | 接口，IrDA |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | MCP2150 |
| 主要屬性： | 帶 PIC18F MCU 的 IrDA 控制器 |
| 次要屬性： | USB 接口 |
| 已供物品： | 板 |
| 產品目錄頁面： | 685 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁
2002 Microchip Technology Inc.
Preliminary
DS21655B-page 9
MCP2150
2.6
Modulation
The data that the MCP2150 UART received (on the TX
pin) that needs to be transmitted (on the TXIR pin) will
need to be modulated. This modulated signal drives the
IR transceiver module. Figure 2-3 shows the encoding
of the modulated signal.
Each bit time is comprised of 16-bit clocks. If the value
to be transmitted (as determined by the TX pin) is a
logic low, then the TXIR pin will output a low level for
7-bit clock cycles, a logic high level for 3-bit clock
cycles or a minimum of 1.6 sec. (see parameter
IR121). The remaining 6-bit clock cycles will be low. If
the value to transmit is a logic high, then the TXIR pin
will output a low level for the entire 16-bit clock cycles.
2.7
Demodulation
The modulated signal (data) from the IR transceiver
module (on RXIR pin) needs to be demodulated to form
the received data (on RX pin). Once demodulation of
the data byte occurs, the data that is received is trans-
mitted by the MCP2150 UART (on the RX pin).
Figure 2-4 shows the decoding of the modulated
signal.
Each bit time is comprised of 16-bit clocks. If the value
to be received is a logic low, then the RXIR pin will be
a low level for the first 3-bit clock cycles or a minimum
of 1.6 s. The remaining 13-bit clock cycles (or differ-
ence up to the 16-bit clock time) will be high. If the value
to be received is a logic high, then the RXIR pin will be
a high level for the entire 16-bit clock cycles. The level
on the RX pin will be in the appropriate state for the
entire 16 clock cycles.
FIGURE 2-3:
ENCODING
FIGURE 2-4:
DECODING
Note:
The signal on the TXIR pin does not actu-
ally line up in time with the bit value that
was transmitted on the TX pin, as shown in
Figure 2-3. The TX bit value is shown to
represent the value to be transmitted on
the TXIR pin.
Note:
The signal on the RX pin does not actually
line up in time with the bit value that was
received on the RXIR pin, as shown in
Figure 2-4. The RXIR bit value is shown to
represent the value to be transmitted on
the RX pin.
BITCLK
TX Bit
TXIR
01
0
1
16 CLK
7 CLK
Start Bit
Data bit 0
Data bit 1
Data bit 2
Data bit ...
24 Tosc
Value
BITCLK
RX
RXIR Bit
01
0
1
≥ 1.6 s (up to 3 CLK)
≥ 13 CLK
16 CLK
Start Bit
Data bit 0
Data bit 1
Data bit 2
Data bit ...
(CLK)
Value
相關PDF資料 |
PDF描述 |
|---|---|
| GBM10DRSN-S664 | CONN EDGECARD 20POS DIP .156 SLD |
| CB5278-000 | HEAT SHRINK TUBING |
| ELC-10D390E | COIL CHOKE 39UH RADIAL |
| CB5270-000 | HEAT SHRINK TUBING |
| VI-BWV-EX | CONVERTER MOD DC/DC 5.8V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP2150-I/P | 功能描述:輸入/輸出控制器接口集成電路 IrDA protocol handlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MCP2150-I/P | 制造商:Microchip Technology Inc 功能描述:IC IRDA CONTROLLER 2150 DIP18 |
| MCP2150-I/SO | 功能描述:輸入/輸出控制器接口集成電路 IrDA protocol handlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| MCP2150-I/SO | 制造商:Microchip Technology Inc 功能描述:IRDA CONTROLLER SMD 2150 SOIC18 |
| MCP2150-I/SORVB | 制造商:Microchip 功能描述:MCP2150 Series 115.2 kBaud 64 Byte Standard Protocol Stack Controller - SOIC-18 |
發布緊急采購，3分鐘左右您將得到回復。