參數資料
型號： MC8640VU1067NC
廠商： Freescale Semiconductor
文件頁數： 25/130頁
文件大小： 0K
描述： MPU DUAL E600 994-FCCBGA
標準包裝： 1
系列： MPC86xx
處理器類型： 32-位 MPC86xx PowerPC
速度： 1.067GHz
電壓： 0.95V
安裝類型： 表面貼裝
封裝/外殼： 994-BCBGA，F(xiàn)CCBGA
供應商設備封裝： 994-FCCBGA（33x33）
包裝： 托盤
MPC8640 and MPC8640D Integrated Host Processor Hardware Specifications, Rev. 3
120
Freescale Semiconductor
System Design Information
The following pins must be left unconnected (floating):
SDn_TX[7:0]
The following pins must be connected to GND:
SDn_RX[7:0]
SDn_REF_CLK
SDn_REF_CLK
NOTE
It is recommended to power down the unused lane through SRDS1CR1[0:7]
register (offset = 0xE_0F08) and SRDS2CR1[0:7] register
(offset = 0xE_0F44.) (This prevents the oscillations and holds the receiver
output in a fixed state.) that maps to SERDES lane 0 to lane 7 accordingly.
For other directions on reserved or no-connects pins see Section 17, “Signal Listings.”
20.6
Pull-Up and Pull-Down Resistor Requirements
The MPC8640 requires weak pull-up resistors (2–10 k
Ω is recommended) on all open drain type pins.
The following pins must not be pulled down during power-on reset: TSEC4_TXD[4], LGPL0/LSDA10,
LGPL1/LSDWE, TRIG_OUT/READY, and D1_MSRCID[2].
The following are factory test pins and require strong pull-up resistors
(100
Ω –1 kΩ) to OV
DD
LSSD_MODE, TEST_MODE[0:3].The following pins require weak pull-up resistors
(2–10 k
Ω) to their
specific power supplies: LCS[0:4], LCS[5]/DMA_DREQ2, LCS[6]/DMA_DACK[2],
LCS[7]/DMA_DDONE[2], IRQ_OUT, IIC1_SDA, IIC1_SCL, IIC2_SDA, IIC2_SCL, and
CKSTP_OUT.
The following pins should be pulled to ground with a 100-
Ω resistor: SD1_IMP_CAL_TX,
SD2_IMP_CAL_TX. The following pins should be pulled to ground with a 200-
Ω resistor:
SD1_IMP_CAL_RX, SD2_IMP_CAL_RX
TSECn_TX_EN signals require an external 4.7-k
Ω pull down resistor to prevent PHY from seeing a valid
Transmit Enable before it is actively driven.
When the platform frequency is 400 MHz, TSEC1_TXD[1] must be pulled down at reset.
TSEC2_TXD[4] and TSEC2_TX_ER pins function as cfg_dram_type[0 or 1] at reset and MUST BE
VALID BEFORE HRESET ASSERTION when coming out of device sleep mode.
20.6.1
Special instructions for Single Core device
The mechanical drawing for the single core device does not have all the solder balls that exist on the single
core device. This includes all the balls for VDD_Core1 and SENSEVDD_Core1 which exist on the
package for the dual core device, but not on the single core package. A solder ball is present for
相關PDF資料
PDF描述
345-012-542-804 CARDEDGE 12POS DUAL .100 GREEN
345-012-542-802 CARDEDGE 12POS DUAL .100 GREEN
MC8640VU1000HC MPU DUAL E600 994-FCCBGA
345-012-542-801 CARDEDGE 12POS DUAL .100 GREEN
MC8640TVU1250HC MPU DUAL E600 994-FCCBGA
相關代理商/技術參數
參數描述
MC8640VU1067NE 功能描述:微處理器 - MPU G8 REV3.0 0.95V 105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC8640VU1250H 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8640VU1250HC 功能描述:MPU DUAL E600 994-FCCBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC86xx 標準包裝:1 系列:MPC85xx 處理器類型:32-位 MPC85xx PowerQUICC III 特點:- 速度:1.2GHz 電壓:1.1V 安裝類型:表面貼裝 封裝/外殼:783-BBGA，F(xiàn)CBGA 供應商設備封裝:783-FCPBGA（29x29） 包裝:托盤
MC8640VU1250N 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series
MC8641DHX1000G 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*