參數資料
型號： MC68HCL05P1ADWR2
廠商： MOTOROLA INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28
封裝： SOIC-28
文件頁數： 62/124頁
文件大小： 623K
代理商： MC68HCL05P1ADWR2
NON-DISCLOSURE
AGREEMENT
REQUIRED
Interrupts
General Release Specification
MC68HC05P1A — Rev. 3.0
42
Interrupts
MOTOROLA
If level sensitivity is chosen, the active high state of the IRQ input can
also activate an IRQ request to the CPU to generate the IRQ interrupt
sequence. This makes the IRQ interrupt sensitive to the following cases:
1. Low level on the IRQ pin.
2. Falling edge on the IRQ pin with all enabled port A interrupt pins
at a high level.
3. Low level on any enabled port A interrupt pin.
4. Falling edge on any enabled port A interrupt pin with all enabled
port A interrupt pins on the IRQ pin at a high level.
This interrupt is serviced by the interrupt service routine located at the
address specified by the contents of $1FFA and $1FFB. The IRQ latch
is automatically cleared by entering the interrupt service routine.
4.5.2 Optional External Interrupts (PA0–PA7)
The IRQ interrupt can be triggered by the inputs on the PA0–PA7 port
pins if enabled by individual mask options. With pullup enabled, each
port A pin can activate the IRQ interrupt function and the interrupt
operation will be the same as for inputs to the IRQ pin. Once enabled by
mask option, each individual port A pin can be disabled as an interrupt
source if its corresponding DDR bit is configured for output mode.
NOTE:
The BIH and BIL instructions apply to the output of the logic OR function
of the enabled PA0–PA7 interrupt pins and the IRQ pin. The BIH and BIL
instructions do not exclusively test the state of the IRQ pin.
NOTE:
If enabled, the PA0–PA7 pins will cause an IRQ interrupt only if these
individual pins are configured as inputs.
4.5.3 Input Capture Interrupt
The input capture interrupt is generated by the 16-bit timer as described
in Section 8. 16-Bit Timer. The input capture interrupt flag is located in
register TSR and its corresponding enable bit can be found in register
TCR. The I bit in the CCR must be clear for the input capture interrupt to
相關PDF資料
PDF描述
MC68HC05P1P 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28
MC68HC05P3CDW 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28
MC68HC05P3P 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28
MC68HC05P3CP 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28
MC68HC05P3DW 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28
相關代理商/技術參數
參數描述
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*