參數資料
型號: MC68HC705C9ACFNE
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
封裝: PLASTIC, LCC-44
文件頁數: 52/118頁
文件大小: 750K
代理商: MC68HC705C9ACFNE
MC68HC05C9A Advance Information Data Sheet, Rev. 4.1
Freescale Semiconductor
39
Chapter 5
Resets
5.1 Introduction
The MCU can be reset four ways: by the initial power-on reset function, by an active low input to the
RESET pin, by the COP, or by the clock monitor. A reset immediately stops the operation of the instruction
being executed, initializes some control bits, and loads the program counter with a user-defined reset
vector address. Figure 5-1 is a block diagram of the reset sources.
Figure 5-1. Reset Sources
5.2 Power-On Reset (POR)
A power-on-reset occurs when a positive transition is detected on VDD. The power-on reset is strictly for
power turn-on conditions and should not be used to detect a drop in the power supply voltage. There is a
4064 internal processor clock cycle (tcyc) oscillator stabilization delay after the oscillator becomes active.
(When configured as a C9A, the RESET pin will output a logic 0 during the 4064-cycle delay.) If the
RESET pin is low after the end of this 4064-cycle delay, the MCU will remain in the reset condition until
RESET is driven high externally.
5.3 RESET Pin
The function of the RESET pin is dependent on whether the device is configured as an MC68HC05C9A
or an MC68HC05C12A. When it is in the MC68HC05C12A configuration, the pin is input only. When in
MC68HC05C9A configuration the pin is bidirectional. In both cases the MCU is reset when a logic 0 is
applied to the RESET pin for a period of one and one-half machine cycles (t
RL
). For the MC68HC05C9A
configuration, the RESET pin will be driven low by a COP, clock monitor, or power-on reset.
VDD
RESET
LATCH
POWER-ON RESET
D
INTERNAL CLOCK
R
RST
TO CPU AND
SUBSYSTEMS
Q
STOP
CLOCK MONITOR
COP WATCHDOG
相關PDF資料
PDF描述
MC68HC705C9AFB 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP44
MC68HC705C9AVFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
MC68HC705C9AP 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP40
MC68HC705C9AFB 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP44
MC68LNC705C9ACFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
相關代理商/技術參數
參數描述
MC68HC705C9ACP 功能描述:IC MCU 2.1MHZ 16K OTP 40-DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C,IrDA,LIN,SPI,UART/USART 外圍設備:DMA,PDR,POR,PVD,PWM,溫度傳感器,WDT 輸入/輸出數:26 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN,36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC705C9ACPE 制造商:Freescale Semiconductor 功能描述:
MC68HC705C9AFNE 功能描述:8位微控制器 -MCU 8B MCU 352 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC705C9AVFNE 功能描述:8位微控制器 -MCU 8B MCU 352 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC705E6CDW 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述: