- 您現在的位置：買賣IC網 > PDF目錄45229 > MC68HC11F1CFN5 (FREESCALE SEMICONDUCTOR INC) 8-BIT, EEPROM, 5 MHz, MICROCONTROLLER, PQCC68 PDF資料下載
參數資料
| 型號： | MC68HC11F1CFN5 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, EEPROM, 5 MHz, MICROCONTROLLER, PQCC68 |
| 封裝： | PLASTIC, LCC-68 |
| 文件頁數： | 86/163頁 |
| 文件大小： | 711K |
| 代理商： | MC68HC11F1CFN5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁
MC68HC11F1
CENTRAL PROCESSING UNIT
MOTOROLA
TECHNICAL DATA
3-5
When an interrupt is recognized, the current instruction finishes normally, the return
address (the current value in the program counter) is pushed onto the stack, all of the
CPU registers are pushed onto the stack, and execution continues at the address
specified by the vector for the interrupt. At the end of the interrupt service routine, an
RTI instruction is executed. The RTI instruction causes the saved registers to be pulled
off the stack in reverse order. Program execution resumes at the return address.
There are instructions that push and pull the A and B accumulators and the X and Y
index registers. These instructions are often used to preserve program context. For
example, pushing accumulator A onto the stack when entering a subroutine that uses
accumulator A, and then pulling accumulator A off the stack just before leaving the
subroutine, ensures that the contents of a register will be the same after returning from
the subroutine as it was before starting the subroutine.
3.1.5 Program Counter (PC)
The program counter, a 16-bit register, contains the address of the next instruction to
be executed. After reset, the program counter is initialized from one of six possible
vectors, depending on operating mode and the cause of reset.
3.1.6 Condition Code Register (CCR)
This 8-bit register contains five condition code indicators (C, V, Z, N, and H), two inter-
rupt masking bits, (I and X) and a stop disable bit (S). In the M68HC11 CPU, condition
codes are automatically updated by most instructions. For example, load accumulator
A (LDAA) and store accumulator A (STAA) instructions automatically set or clear the
N, Z, and V condition code flags. Pushes, pulls, add B to X (ABX), add B to Y (ABY),
and transfer/exchange instructions do not affect the condition codes. Refer to Table
3-2, which shows what condition codes are affected by a particular instruction.
3.1.6.1 Carry/Borrow (C)
The C bit is set if the arithmetic logic unit (ALU) performs a carry or borrow during an
arithmetic operation. The C bit also acts as an error flag for multiply and divide opera-
tions. Shift and rotate instructions operate with and through the carry bit to facilitate
multiple-word shift operations.
3.1.6.2 Overflow (V)
The overflow bit is set if an operation causes an arithmetic overflow. Otherwise, the V
bit is cleared.
Table 3-1 Reset Vector Comparison
POR or RESET Pin
Clock Monitor
COP Watchdog
Normal
$FFFE, F
$FFFC, D
$FFFA, B
Test or Boot
$BFFE, F
$BFFC, D
$BFFA, B
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11F1CPU4R2 | 8-BIT, EEPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC11F1CFN3 | 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1CFN2 | 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1VFN2 | 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1MFN3 | 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11F1CFU | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1CFU1 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1CFU3 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1CFU4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1CPU2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。