- 您現在的位置：買賣IC網 > PDF目錄45229 > MC68HC11F1CFN5 (FREESCALE SEMICONDUCTOR INC) 8-BIT, EEPROM, 5 MHz, MICROCONTROLLER, PQCC68 PDF資料下載
參數資料
| 型號： | MC68HC11F1CFN5 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, EEPROM, 5 MHz, MICROCONTROLLER, PQCC68 |
| 封裝： | PLASTIC, LCC-68 |
| 文件頁數： | 124/163頁 |
| 文件大?。?/td> | 711K |
| 代理商： | MC68HC11F1CFN5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁當前第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁
MC68HC11F1
RESETS AND INTERRUPTS
MOTOROLA
TECHNICAL DATA
5-1
SECTION 5 RESETS AND INTERRUPTS
Resets and interrupt operations load the program counter with a vector that points to
a new location from which instructions are to be fetched. A reset causes the internal
control registers to be initialized to a known state. The program counter is loaded with
a known starting address and execution of instructions begins. An interrupt temporarily
suspends normal program execution while an interrupt service routine is being execut-
ed. After an interrupt has been serviced, the main program resumes as if there had
been no interruption.
5.1 Resets
There are four possible sources of reset. Power-on reset (POR) and external reset
share the normal reset vector. The computer operating properly (COP) reset and the
clock monitor reset each has its own vector.
5.1.1 Power-On Reset
A positive transition on VDD generates a power-on reset (POR), which is used only for
power-up conditions. POR cannot be used to detect drops in power supply voltages.
A 4064 tcyc (internal clock cycle) delay after the oscillator becomes active allows the
clock generator to stabilize. If RESET is at logical zero at the end of 4064 tcyc, the CPU
remains in the reset condition until RESET goes to logical one.
It is important to protect the MCU during power transitions. To protect data in EE-
PROM, M68HC11 systems need an external circuit that holds the RESET pin low
whenever VDD is below the minimum operating level. This external voltage level de-
tector, or other external reset circuits, are the usual source of reset in a system. The
POR circuit only initializes internal circuitry during cold starts. Refer to Figure 2–3.
5.1.2 External Reset (RESET)
The CPU distinguishes between internal and external reset conditions by sensing
whether the reset pin rises to a logic one in less than two E-clock cycles after an inter-
nal device releases reset. When a reset condition is sensed, the RESET pin is driven
low by an internal device for four E-clock cycles, then released. Two E-clock cycles
later it is sampled. If the pin is still held low, the CPU assumes that an external reset
has occurred. If the pin is high, it indicates that the reset was initiated internally by ei-
ther the COP system or the clock monitor. It is not advisable to connect an external
resistor capacitor (RC) power-up delay circuit to the reset pin of M68HC11 devices be-
cause the circuit charge time constant can cause the device to misinterpret the type of
reset that occurred.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11F1CPU4R2 | 8-BIT, EEPROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| MC68HC11F1CFN3 | 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1CFN2 | 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1VFN2 | 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PQCC68 |
| MC68HC11F1MFN3 | 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11F1CFU | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1CFU1 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1CFU3 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1CFU4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:ROM-based high-performance microcontrollers |
| MC68HC11F1CPU2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。