- 您現在的位置：買賣IC網 > PDF目錄45228 > MC68HC11E9VFU2 (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MC68HC11E9VFU2 |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | QFP-64 |
| 文件頁數： | 117/242頁 |
| 文件大?。?/td> | 1672K |
| 代理商： | MC68HC11E9VFU2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁當前第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁
Allowing for Bootstrap Mode
M68HC11 Bootstrap Mode, Rev. 1.1
Freescale Semiconductor
203
After the MCU sends $FF [8], it enters the WAIT1 loop [9] and waits for the first data character from the
host. When this character is received [10], the MCU programs it into the address pointed to by the Y index
register. When the programming time delay is over, the MCU reads the programmed data, transmits it to
the host for verification [11], and returns to the top of the WAIT1 loop to wait for the next data character
[12]. Because the host previously sent the second data character, it is already waiting in the SCI receiver
of the MCU. Steps [13], [14], and [15] correspond to the second pass through the WAIT1 loop.
Back in the host, the first verify character is received, and the third data character is sent [6]. The host
then waits for the second verify character [7] to come back from the MCU. The sequence continues as
long as the host continues to send data to the MCU. Since the WAIT1 loop in the PROGRAM utility is an
indefinite loop, reset is used to end the process in the MCU after the host has finished sending data to be
programmed.
Allowing for Bootstrap Mode
Since bootstrap mode requires few connections to the MCU, it is easy to design systems that
accommodate bootstrap mode.
Bootstrap mode is useful for diagnosing or repairing systems that have failed due to changes in the
CONFIG register or failures of the expansion address/data buses, (rendering programs in external
memory useless). Bootstrap mode can also be used to load information into the EPROM or EEPROM of
an M68HC11 after final assembly of a module. Bootstrap mode is also useful for performing system
checks and calibration routines. The following paragraphs explain system requirements for use of
bootstrap mode in a product.
Mode Select Pins
It must be possible to force the MODA and MODB pins to logic 0, which implies that these two pins should
be pulled up to VDD through resistors rather than being tied directly to VDD. If mode pins are connected
directly to VDD, it is not possible to force a mode other than the one the MCU is hard wired for. It is also
good practice to use pulldown resistors to VSS rather than connecting mode pins directly to VSS because
it is sometimes a useful debug aid to attempt reset in modes other than the one the system was primarily
designed for. Physically, this requirement sometimes calls for the addition of a test point or a wire
connected to one or both mode pins. Mode selection only uses the mode pins while RESET is active.
RESET
It must be possible to initiate a reset while the mode select pins are held low. In systems where there is
no provision for manual reset, it is usually possible to generate a reset by turning power off and back on.
RxD Pin
It must be possible to drive the PD0/RxD pin with serial data from a host computer (or another MCU). In
many systems, this pin is already used for SCI communications; thus no changes are required.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC711E20CFN2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PQCC52 |
| MC68L11E0B2 | 8-BIT, 2 MHz, MICROCONTROLLER, PDIP56 |
| MC68HC11E9CPB3 | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PQFP52 |
| MC68HC11E1VB2 | 8-BIT, 2 MHz, MICROCONTROLLER, PDIP56 |
| MC68HC11E9BCFU2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11E9VPB2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers |
| MC68HC11EA9 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8 BIT HCMOS SINGLE CHIP MICROCONTOROLLER WITH A/D CONVERTER |
| MC68HC11EA9BCFN2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers |
| MC68HC11EA9CFN2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers |
| MC68HC11EA9CFN3 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。