- 您現在的位置：買賣IC網 > PDF目錄376151 > MC1451A-E (Electronic Theatre Controls, Inc.) Advanced Brushless Motor Control Chipset PDF資料下載
參數資料
| 型號： | MC1451A-E |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Brushless Motor Control Chipset |
| 中文描述： | 先進的無刷電機控制芯片組 |
| 文件頁數： | 58/70頁 |
| 文件大?。?/td> | 474K |
| 代理商： | MC1451A-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
58
SET_PHASE_2
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set waveform mode to 2-phase
none
74 (hex)
global
all
no
SET_PHASE_2 sets the current commutation waveformto 2-phase. In
this scheme the commutated output signals have a phase separation of
90 degrees.
SET_PHASE_HALL
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set phase initialization to Hall-based
none
78 (hex)
current axis
all
no
SET_PHASE_HALL sets the phase initialization mode to Hall-based. In
this mode the phasing of the motor is initialized immediately after the
host sends an INIT_PHASE command by reading the state of the three
Hall-sensors. Phasing is completed automatically after the motor has
moved through one full rotation.
SET_PHASE_ALGOR
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set phase initialization to algorithmic
none
79 (hex)
current axis
all
no
SET_PHASE_ALGOR sets the phase initialization mode to algorithmc.
In this mode the phasing of the motor is initialized by applying energy to
the windings and observing the resultant motor motion. Before the
phase initialization routine can be performed the motor must be in open
loop mode (MTR_OFF command). The amount of time that the chipset
waits to initialize the phase after applying energy is set using the
command SET_PHASE_TIME. Before phase initialization occurs the
amount of energy to apply to the motor is set using the command
SET_BUF_MTR_CMD. To actually begin the algorithmc initialization
procedure the command INIT_PHASE is used.
SET_PHASE_ENC
Set commutation mode to encoder-
based
none
5f (hex)
current axis
all
no
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
SET_PHASE_ENC sets the commutation mode to encoder-based. This
is the normal operating mode of the MC1231A chipset. In this mode the
commutation angle is determned by the encoder location (maintained
continuously by chipset) , the initial phase offset value (determned
during phase initialization sequence) , and the #of encoder counts per
electrical cycle (provided by host).
SET_PHASE_MICRO
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set commutation mode to microstepping
none
63 (hex)
current axis
all
no
SET_PHASE_MICRO sets the commutation mode to mcrostepping.
This is not the normal operating mode of the MC1231A chipset and
should only be used during phase initialization if the algorithmc or Hall-
based methods can not be used.
PRESCALE_ON
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set encoder prescalar on
none
0d (hex)
current axis
all
no
PRESCALE_ON enables the encoder prescalar function which reduces
the rate of encoder counts used for commutation by a factor of 64.
This command does not affect the actual axis position, the servo
filter output, or any other encoder-related functions other than
those used directly for commutation.
This command should only be used when the commutation mode
is encoder-based, and when the motor is not in motion.
PRESCALE_OFF
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set encoder prescalar off
none
0e (hex)
current axis
all
no
PRESCALE_OFF disables the encoder prescalar function which
reduces the rate of encoder counts used for commutation by a factor of
64.
SET_PHASE_CNTS
Set number of encoder counts per
commutation cycle
1/write
75 (hex)
current axis
all
no
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
SET_PHASE_CNTS sets the number of encoder counts per
commutation electrical cycle. The associated data word is an unsigned
16 bit number, with an allowed range of 129 to 32,767.
相關PDF資料 |
PDF描述 |
|---|---|
| MC1101A-P | Advanced Brushless Motor Control Chipset |
| MC1211N | LSI CMOS |
| MCY1210N | LSI CMOS |
| MC14005N | 8-function calculator unit co-operating with LED display |
| MC74005N | 8-function calculator unit co-operating with LED display |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1451CCP | 制造商:PMD 功能描述: |
| MC14520B | 制造商:Motorola Inc 功能描述: 制造商:ON Semiconductor 功能描述: |
| MC14520BAL | 制造商:Motorola Inc 功能描述:Counter, Up, 4 Bit Binary, 16 Pin, Ceramic, DIP |
| MC14520BCP | 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
| MC14520BCPG | 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。