- 您現在的位置：買賣IC網 > PDF目錄376151 > MC1451A-E (Electronic Theatre Controls, Inc.) Advanced Brushless Motor Control Chipset PDF資料下載
參數資料
| 型號： | MC1451A-E |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Advanced Brushless Motor Control Chipset |
| 中文描述： | 先進的無刷電機控制芯片組 |
| 文件頁數： | 51/70頁 |
| 文件大?。?/td> | 474K |
| 代理商： | MC1451A-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
51
MULTI_UPDATE
Immediately update parameters for
multiple axis
1/write
5b (hex)
set by data word
all axes
no
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
MULTI_UPDATE immediately updates the profile and filter parameters
for 1 or more axis simultaneously. For each updated axis, the axis
behaves as if a separate UPDATE command had been given for each
axis. The associated data word contains a "positive-sense" bit mask for
each axis. A one (1) in the axis bit position indicates the axis will be
updated. A zero (0) indicates it will not. The following table shows this
bit encoding:
Bit #
0
1
2-15
Axis #updated
1
2
unused, must be set to 0
SET_AUTO_UPDATE_ON
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set automatic profile update on
none
5c (hex)
current
all axes
no
SET_AUTO_UPDATE_ON sets the automatic profile update
mechanismon. After this command is sent, a satisfied breakpoint
condition will result in all of the double-buffered profile and filter
parameters automatically being transferred to the active registers. Once
set to this mode, the axis will stay in this mode until explicitly
commanded out using the SET_AUTO_UPDATE_OFF command.
SET_AUTO_UPDATE_OFF
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set automatic profile update off
none
5d (hex)
current
all axes
no
SET_AUTO_UPDATE_OFF sets the automatic profile update
mechanismoff. After this command is sent, a satisfied breakpoint
condition will
not
result in the double-buffered profile and filter
parameters automatically being transferred to the active registers. Once
set to this mode, the axis will stay in this mode until explicitly
commanded out using the SET_AUTO_UPDATE_ON command.
When in this mode, the only way that profile parameters can be
updated is through the UPDATE or the MULTI_UPDATE
commands.
GET_BRK_PNT
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Get break point comparison value
2/read
57 (hex)
current axis
all axes
no
GET_BRK_PNT returns the breakpoint comparison value set using the
SET_BRK_PNT command. The returned value is a 32-bit number with
units of either servo loops or counts (depending on the current
breakpoint mode).
Interrupt Processing
SET_INTRPT_MASK
Data/direction:
Encoding:
Axis acted on:
Available on:
Double buffered:
Set host interrupt mask
1/write
2f (hex)
current axis
all axes
no
SET_INTRPT_MASK sets the interrupt mask so that interrupt events
can be individually masked off. When a non-masked interrupt occurs in
any axis, the interrupt signal to the host is activated (HostIntrpt pin on
I/O chip). The host can choose to ignore or respond to the interrupt.
Once an interrupt has been generated, no new interrupts will be
generated until a RST_INTRPT command is given, after which the
interrupt signal to the host will be cleared, and a new interrupt (on any
axis) can be generated. The associated data word is encoded as a field
of bits, with each bit representing a possible interrupting condition. A 1
value in the mask bit will cause the corresponding event to generate an
interrupt, while a 0 will stop the corresponding event frominterrupting
the host. The bit encoding is as follows:
Bit #
0
1
2
3
4
5
6
7
8-10
11
12-15
Event
Motion complete
position wrap-around
update breakpoint reached
position capture received
motion error
positive limt switch
negative limt switch
command error
not used, must be set to 0
commutation error
not used, may be set to 0 or 1
相關PDF資料 |
PDF描述 |
|---|---|
| MC1101A-P | Advanced Brushless Motor Control Chipset |
| MC1211N | LSI CMOS |
| MCY1210N | LSI CMOS |
| MC14005N | 8-function calculator unit co-operating with LED display |
| MC74005N | 8-function calculator unit co-operating with LED display |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1451CCP | 制造商:PMD 功能描述: |
| MC14520B | 制造商:Motorola Inc 功能描述: 制造商:ON Semiconductor 功能描述: |
| MC14520BAL | 制造商:Motorola Inc 功能描述:Counter, Up, 4 Bit Binary, 16 Pin, Ceramic, DIP |
| MC14520BCP | 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
| MC14520BCPG | 功能描述:計數器移位寄存器 3-18V Dual BCD Up RoHS:否 制造商:Texas Instruments 計數器類型: 計數順序:Serial to Serial/Parallel 電路數量:1 封裝 / 箱體:SOIC-20 Wide 邏輯系列: 邏輯類型: 輸入線路數量:1 輸出類型:Open Drain 傳播延遲時間:650 ns 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。